Blue Sea 9001e E-series Battery Switch (Blue Sea Systems) 5076

Review for blue sea 9001e battery switch

Price was $44.78. This is a great switch. The dual circuit design allow me to switch both the engine electrical and the "house" electrical on at the same time and still keep them isolated. In refurbishing my boat, i isolated the house wiring from the engine wiring so i could consume the battery power overnight and not worry about starting the engine in the morning. This switch made that possible. The plus feature allows both to be combined in an extraordinary situation or for charging. My issue in the past has been i would forget to isolate the batteries and end up running both down. So this is used normally in the off or on position only. I also installed the blue sea systems e series automatic charging relay to let the boat maintain the battery charges without any intervention. Was able to test this after using a 110v converter to watch tv and blu ray movie long enough to run down the house battery. Engine started and charge its battery for a few minutes and then the house battery was added and began to rapidly charge. I can't mess up now.

-J. Nielsen

Blue Sea 9001e E-series Battery Switch Sporting Goods 9001e

  1. Special: Selector 4 Position. Switches isolated battery banks to all loads or combines battery banks to all loads
  2. Special: IP66 waterproof, ISO 8846 and meets ABYC requirements
  3. Special: Ignition protected-safe for installation aboard gasoline powered boats

Blue-sea-9001e-battery-switch: Blue Sea Systems Sporting Goods Blue Sea Systems E-series Battery Switches. Switches Battery Bank 1 Or Battery Bank 2 Or

Buy Now

Content

Selector 4 Position. Switches Isolated Battery Banks To All Loads Or Combines Battery Banks To All Loads, Ignition Protected-safe For Installation Aboard Gasoline Powered Boats, IP66 Waterproof, ISO 8846 And Meets ABYC Requirements, Terminal Stud Size: 3/8" - 16, Continuous Rating: 350A, Maximum Voltage: 32V DC, Special Blue Sea 9001E E-Series Battery Switch.

Bonus: Blue Sea 9001e E-series Battery Switch

Automotive Blue Sea 9001e E-series Battery Switch 9001e Half Price Automotive Parts And Accessories 700115568746 Blue Sea Systems, Blue Sea 9001e E-series Battery Switch 0799916893171. blue sea systems e-series battery switches. switches battery bank 1 or battery bank 2 or battery banks 1 and 2 to all loads using one switch. up to 350 amperes continuous rating ignition protected - safe for installation aboard gasoline powered boats. tactile indicator conveys knob position by feel only. fits all perko and guest low amperage battery switch hole patterns. case design allows surface or rear panel mounting. accepts up to 4/0 awg battery cables. meets american boat and yacht council (abyc) requirements for battery switches. make-before-break contact design on 9001 and 9002 models allows switching between battery banks without power interruption. Blue Sea 9001e E-series Battery Switch Sporting Goods 9001e.

Blue Sea 9001E E-Series Battery Switch Overview (9001E)

Blue Sea 9001e E-series Battery Switch

  • Order : Automotive
  • Brand : Blue Sea Systems
  • Color : Red
  • Creator : Blue Sea Systems
  • EAN : 0799916893171
  • Manufacturer : Acr Electronics
  • ManufacturerPartsWarrantyDescription : Parts
  • Model : 9001e
  • MPN : 9001E
  • Total Items : 1
  • Quantity : 1
  • Part Number : 9001E
  • Group : Automotive Parts And Accessories
  • Category : SPORTING GOODS
  • ReleaseDate : 2011-01-10
  • Size : One Size
  • Title : Blue Sea 9001E E-Series Battery Switch
  • UPC : 700115568746

Bonus Blue-sea-9001e-battery-switch

Acr Electronics Automotive 9001e: Blue Sea 9001E E-Series Battery Switch

  • Selector 4 Position. Switches Isolated Battery Banks To All Loads Or Combines Battery Banks To All Loads
  • Arnold 16-Inch Battery Cable Set
  • Camco 47480 Red 3/8" Stud 18" Long 2-Gauge Marine Battery Cable And Tinned Lug Assembly
  • Blue Sea Systems ST Blade Fuse Block - 12 Circuits With Negative Bus & Cover
  • New Dual Group 27 Battery Tray T-h Marine Dbh27pdp Dual Battery Holder Fits Group 27
  • Blue Sea Systems 10 Gang Common 150A Busbar With Cover
  • Attwood Battery Tray- 27 Series
  • NOCO HM318BKS Group 24-31 Snap-Top Battery Box For Automotive, Marine, And RV Batteries
  • Camco 47470 Black 5/16" Stud 18" Long 2-Gauge Marine Battery Cable And Lug Assembly Tinned
  • Ancor 108802 Marine Grade Electrical Primary Tinned Copper Boat Wiring (10-Gauge, Red, 25-Feet)
  • Blue Sea Systems 285-Series Surface Mount 50A Circuit Breaker
  • IP66 Waterproof, ISO 8846 And Meets ABYC Requirements
  • Ignition Protected-safe For Installation Aboard Gasoline Powered Boats
Half Price

Product arrived as advertised. Made of durable dense plastic. Main mechanism is tightly sealed. Mounted to battery reservoir/compartment in my boat. Did not come with mounting screws. Mounted to surface of aluminum/side and switch has large gaps along 3 sides to accommodate wire connections after mounting (don't forget to connect the wires before you mount if you can't get behind the switch). Ran a main positive connection from battery to input of switch then connected primary output to mercury motor-ignition. Also added another positive lead to the primary input for a fuse block (blue seas 5026) which comes out of the switches output. Now i can kill both motor-ignition-console and fuse block with accessories. Combined with the fuse block it completely organized the nightmare of wires and cables as well as kills all drain from the main battery.

blue-sea-9001e-battery-switch
Click to see NoticeBlue Sea 9001e E-series Battery Switch (Blue Sea Systems)"Works"

Blue Sea 9001E E-Series Battery Switch | MobileView

Blue-sea-9001e-battery-switch

Blue Sea 9001E E-Series Battery Switch

Blue Sea Systems 10 Gang Common 150A Busbar with Cover

The Industry Standard Busbar For Positive Or Negative Power Distribution Bus Material - Tin Platted Copper Cda 110/uns C1100 Insert Molded Stainless Steel Studs Eliminate Need For Securing Nut And Allow High Torqueing Electrical Contact.

Blue Sea Systems 10 Gang Common 150A Busbar with Cover

Blue-Sea-Systems-Common-Busbar

BLUE SEA SYSTEMS 10 GANG COMMON 150A BUSBAR WITH COVER Review
Brand :    blue sea systems
Color :    With Cover
Size :    150A
Weight :    0.30 pounds
Model :    2300
Quantity :    1
Order click here :    normally ships in 24 hours
Sports :    Best Sporting Goods (blue sea systems) reviews for Blue Sea Systems 10 Gang Common 150A Busbar with Cover available as-of ( Sep 2019 )
Max voltage: 300V AC/ 48V DCContinuous Rating: 130A AC/ 150A DCReinforced polycarbonate base with tin plated pure electrical copper for maximum conductivity2 mounting holes accept #10 (M5) screws150A Common BusBar with 10 screws and a cover

Blue Sea Systems ST Blade Fuse Block - 12 Circuits with Negative Bus & Cover

Fuse Block Atc/ato 12 Circuit W/negative Bus And Cover Mfg 5026 32vdc Max W/30amp Max Per Circuit & 100amp Per Block. 3. 32"w X 6. 5"h X 1. 52"d. Fuses Sold Separately.

Blue Sea Systems ST Blade Fuse Block - 12 Circuits with Negative Bus & Cover

Blue-Sea-Systems-Blade-Block

BLUE SEA SYSTEMS ST BLADE FUSE BLOCK - 12 CIRCUITS WITH NEGATIVE BUS & COVER Advantages
Brand :    blue sea systems
Size :    one size
Weight :    0.80 pounds
Model :    5026
Quantity :    1
Order click here :    normally ships in 24 hours
Sports :    Best Sporting Goods (blue sea systems) reviews for Blue Sea Systems ST Blade Fuse Block - 12 Circuits with Negative Bus & Cover available as-of ( Sep 2019 )
St blade fuse block - 12 circuits with negative bus and coverAccepts ATO and ATC fast acting blade fusesPositive distribution bus with #10-32 studCan be used for 24-hour circuitsCover satisfies ABYC/USCG Requirements for insulation, incorporates an easy to open push button latch providing easy access to fuses, storage for two spare fuses

Arnold 16-Inch Battery Cable Set

If You Want Your Outdoor Power Equipment To Last Longer And Do More You Want Arnold Parts Accessories And Attachments. Providing You With A Wide Variety Of Hassle-free Top-quality Products Arnold Parts Will Keep All Your Equipment In The Best Shape Possible. Compatible With Tons Of Major Brands 50+ Years Of Proven Performance Has Landed Arnold A Reputation Of Cutting Edge Product Innovations And Extensive Engineering Expertise. From Basic Maintenance To Major Innovations Arnold Has Everything You Need To Keep Equipment Running The Way It Should Season After Season. With Arnold You Can Be Confident Of A Reliable Product With Accurate Fit Design Material And Construction. In Addition To Reliable Parts And Accessories Arnolds Easy-to-follow Instructions And Extra Tips Will Ease Your Equipment Maintenance And Assure That You Get The Job Done Right.

Arnold 16-Inch Battery Cable Set

Arnold-16-Inch-Battery-Cable-Set

ARNOLD-16-INCH-BATTERY-CABLE-SET-(OUTDOOR-LIVING)

Image of Arnold-16-inch-battery-cable-set-(outdoor-living)
Arnold-16-inch-battery-cable-set-(outdoor-living)"Arnold 16-inch Battery Cable Set Outdoor Living Bc 16pn Tp
  1. Products: Contains set of positive and negative cables
  2. Products: All copper conductor with polyvinyl insulation
  3. Products: Crimped aluminum terminals
Arnold-16-inch-battery-cable-set: Arnold Outdoor Living If You Want Your Outdoor Power Equipment To Last Longer And Do More You Want Arnold Parts Accessories "
ARNOLD 16-INCH BATTERY CABLE SET Highlight
Brand :    arnold
Weight :    0.20 pounds
Model :    BC-16PN-TP
Quantity :    1
Order click here :    normally ships in 24 hours
Lawn & Patio :    Best Outdoor Living (arnold) reviews for Arnold 16-Inch Battery Cable Set available as-of ( Sep 2019 )
All copper conductor with polyvinyl insulation1/2" round center hole, 16" lengthCrimped aluminum terminalsContains set of positive and negative cables

New Dual Group 27 Battery Tray t-h Marine Dbh27pdp Dual Battery Holder Fits Group 27

New Dual Group 27 Battery Tray T-h Marine Dbh27pdp Dual Battery Holder Fits Group 27 : Holds Two Series 27 Deep Cycle Batteries Side By Side. Patented Poly Strap With Quick Release Buckle. Meets All Nmma Specs For Battery Retention. 14-1/2" L X 13-1/8"w X 1" H.

New Dual Group 27 Battery Tray t-h Marine Dbh27pdp Dual Battery Holder Fits Group 27

Group-Battery-Marine-Dbh27pdp-Holder

Ancor 108802 Marine Grade Electrical Primary Tinned Copper Boat Wiring (10-Gauge, Red, 25-Feet)

Ancor Marine Gradetm Wire Is Manufactured From Tinned Copper Stranding For Maximum Protection Against Corrosion And Electrolysis. Ultra Flexible (type 3) Stranding Resists Fatigue Due To Vibration And Flexing.

Ancor 108802 Marine Grade Electrical Primary Tinned Copper Boat Wiring (10-Gauge, Red, 25-Feet)

Ancor-108802-Electrical-Primary-10-Gauge

ANCOR 108802 MARINE GRADE ELECTRICAL PRIMARY TINNED COPPER BOAT WIRING (10-GAUGE, RED, 25-FEET) Advantages
Brand :    ancor
Color :    Red
Size :    25 Feet
Weight :    0.35 pounds
Model :    108802
Quantity :    1
Order click here :    normally ships in 24 hours
Sports :    Best Sporting Goods (ancor) reviews for Ancor 108802 Marine Grade Electrical Primary Tinned Copper Boat Wiring (10-Gauge, Red, 25-Feet) available as-of ( Sep 2019 )
Exceeds all UL 1426, US Coast Guard Charter boat (CFR title 46) and ABYC standardsManufactured from individual copper strands and tinned to perform in the harshest marine environments.They are constructed with premium vinyl insulation that is rated at 600 volts, 105 deg C dry and 75 deg C wet, stays flexible even in extreme cold (-40 deg F/C) and resists salt water, battery acid, oil, gasoline, heat, abrasion and ultra-violet radiation.Ultra-flexible Type 3 stranding resists fatigue from vibration and provides added corrosion protection.

Attwood Battery Tray- 27 Series

A Simple-to-install Battery Holder That Fits Into A Limited Space. For Batteries Up To 10-1/2 Inch In Height. Provides Simple Installation For Changing Or Replacing Batteries. The Polypropylene Hold-down Strap Has A Positive Locking Quick Disconnect Buckle. Molded Base Mounts With Four 10 Pinhead Screws.

Attwood Battery Tray- 27 Series

Attwood-Battery-Tray-27-Series

ATTWOOD BATTERY TRAY- 27 SERIES Features
Brand :    attwood
Weight :    0.50 pounds
Model :    9093-5
Quantity :    1
Order click here :    normally ships in 24 hours
Sports :    Best Sporting Goods (attwood) reviews for Attwood Battery Tray- 27 Series available as-of ( Sep 2019 )
27 series TrayFor batteries up to 10-1/2" in height.Battery series 27/27MProvides simple installation for changing or replacing batteriesA simple-to-install battery holder that fits into a limited space12-3/8 inches L x 7-1/8 inches w

Blue Sea Systems 285-Series Surface Mount 50A Circuit Breaker

Drop In Replacement For 185-series Circuit Breakers Visible Reset Lever Shows Open Condition "trip Free" Design Cannot Be Held "on" During Fault Current Condition.

Blue Sea Systems 285-Series Surface Mount 50A Circuit Breaker

Blue-Sea-Systems-Surface-Circuit

BLUE SEA SYSTEMS 285-SERIES SURFACE MOUNT 50A CIRCUIT BREAKER Highlight
Brand :    blue sea systems
Color :    Surface Mount
Size :    50A
Weight :    0.30 pounds
Model :    7183
Quantity :    1
Order click here :    normally ships in 24 hours
Sports :    Best Sporting Goods (blue sea systems) reviews for Blue Sea Systems 285-Series Surface Mount 50A Circuit Breaker available as-of ( Sep 2019 )
Visible reset lever shows open conditionDrop in replacement for 185-Series Circuit BreakersTrip Free design cannot be held "ON" during fault current conditionTerminal Size: 1/4" Ring TerminalMax Voltage: 48V DC, Interrupt Capacity: 3000A @ 48V

Camco 47480 Red 3/8" Stud 18" Long 2-Gauge Marine Battery Cable and Tinned Lug Assembly

Camco's 12" 2 Awg 3/8" Stud Premium Marine Quality Battery Cable Wire Is Ul 1426 Listed And Manufactured To The Highest Abyc Standards. Heat-resistant Up To 105c Dry And Available In Black Red And Yellow. Pre-assembled With Premium Marine Quality Tin Plated 95%-copper Lugs Each Strand Of Individually Tinned Wire Provides The Greatest Protection Against Corrosion And Oxidation Available. Camco's Type 3 Boat Cable Wire Stays Ultra Flexible Even In The Most Extreme Conditions.

Camco 47480 Red 3/8" Stud 18" Long 2-Gauge Marine Battery Cable and Tinned Lug Assembly

Camco-47480-2-Gauge-Battery-Assembly

CAMCO 47480 RED 3/8" STUD 18" LONG 2-GAUGE MARINE BATTERY CABLE AND TINNED LUG ASSEMBLY Summary
Brand :    camco
Color :    Red
Size :    18 Inch
Model :    47480
Quantity :    1
Order click here :    normally ships in 24 hours
Automotive Parts And Accessories :    Best Auto Accessory (camco) reviews for Camco 47480 Red 3/8" Stud 18" Long 2-Gauge Marine Battery Cable and Tinned Lug Assembly available as-of ( Sep 2019 )
2 AWG wire, fits 3/8" studTin plated 95% copper lugs for superior corrosion and oxidation resistanceHeat resistant up to 105C dryType 3 boat cable wire stays ultra flexible even in the most extreme conditionsUL 1426 listed and manufactured to the highest ABYC standards

NOCO HM318BKS Group 24-31 Snap-Top Battery Box for Automotive, Marine, and RV Batteries

The Noco Snap-top Battery Box Is Designed For Group 24-31 Batteries. The Snap-top Design Effectively Collects Electrolytes Allows Ventilation Secures And Locks Lid To Prevent Accidental Contact Of Underground Battery Terminals. Ideal For Automotive Marine And Rv Applications. Resistant To Uv Exposure. Meets Uscg Code Of Federal Regulations 183. 420 And Abyc E-10. 7 Specification.

NOCO HM318BKS Group 24-31 Snap-Top Battery Box for Automotive, Marine, and RV Batteries

NOCO-HM318BKS-Snap-Top-Automotive-Batteries

Review from E. Kathlene, Hackney Simple And Easy. Used This On My Car Trailer For Aux Batt And Actually Bolted The Box To The Floor Of The Trailer (comes With Strap Mounting Bosses - Plastic And A Strap) Which I Felt Was Most Secure. The Lid Has A Clasp On Either Side Simple Wedge That Holds Against The Body Of The Box. Press The Wedge In And Lift Off. One Side Has Plenty Of Room For Wiring To Come Up And Out While Still Under The Lid. Also Has A Slip Into Grove Style Divider Piece For Smaller Series Batteries. Mine Was A Group 31 Agm Big Rig Battery And It Fit Excellently!

Noco Hm318bks Group 24-31 Snap-top Battery Box Automotive, Marine, Rv Batteries (Auto Accessory) Review

Review from N. Annette, Redbridge 
Clasps On Side Are Hard To Open Because The Case Bottom Bends Inward When You Push On The Clasp (part Of The Top). I Had To Stick A Broad Bladed Screwdriver Between Clasp And Retainer To Get It Open. You Might Think This Is A Safety Feature Designed To Prevent The Case From Opening Unexpectedly But I Don't Think So. You Should Be Securing The Top With The Included Safety Strap So The Clasps Are Mostly There To Keep The Top From Shifting Around. Second Thing. The Product Posting Asserts Support For Group 31 Batteries (in Several Places Including The Product Picture). What I Received Only Claims Support For Group 30 Batteries See Pic. I Don't Think This Is An Actual Problem For Me I Measured The Inside Dimensions Of The Case And They Do Appear Big Enough For The Group 31 Battery I Have On Order (according To The Battery Specs I Have Not Received The Battery Yet). Niether Of These Things Adds To My Opinion Of The Product.
NOCO-HM318BKS-GROUP-24-31-SNAP-TOP-BATTERY-BOX-AUTOMOTIVE,-MARINE,-RV-BATTERIES-(AUTO-ACCESSORY)
Image of Noco-hm318bks-group-24-31-snap-top-battery-box-automotive,-marine,-rv-batteries-(auto-accessory)"I Bought This Model To Match The Other Group 24 Box I Have On My Trailer. The Box Works Well Provides Room For The Wires To Exit Easily And Because I Had Limited Room Allows Easy Modification. I Had To Remove The Finger Hold Handle At One End Of Each Box To Make Them Fit In The Area I Had. They Came Off Easily With A Hand Saw Did Not Open Up Any Holes In The Box Itself And Made The Job Very Easy. Bottom Line This Is A Quality Box That Does What It Is Supposed To Do. One Issue I Do Have Is That The Supplied Strap Is Not Quite The Quality I Would Have Liked. The Plastic Buckle Is Difficult To Use And Can Break If You Are Not Careful. This Is Not An Uncommon Problem With Plastic Battery Boxes But I Thought I Should Mention It."

Bought A Large Deep Cycle Marine Battery For My Cpap And Wanted Something To House Battery In My Bedroom And Contain Any Potential Battery Leakage. This Thing Was Perfect. There Is A Movable Divider In The Box To Keep Battery From Shifting Around Which Will Accommodate Every Car Or Marine Sized Battery I've Seen. Comes With Strap And Hardware To Mount Box To Vehicle/vessel If Required. Handles On Each End Of The Box Make My 65lb. Battery Easy To Pick Up With Two Hands And Carry Much Better Than Using The Battery Handle Mounted To The Center Of The Battery. This Is A Very Good Value And I'm Glad I Did Not Spend Two To Three Times As Much For Other Similar Boxes.

L. Anonymous, Solihull

Hard To Beat The Value. The 6 Volt Size Will Perfectly Fit A Trojan T105 Or Most 220 Amphour 6 Volts. I Mounted Mine On An Angle Iron Rack Built Into A Travel-trailer Tongue So The Box Material Did Not Have To Be Structurally Rigid. This Will Protect Well Against Water Or Rocks From The Roadway. There Is A Shielded Gap In The Lid Where You Can Run A Connecting Cable To A Second 6 Volt For Use In A Series. The Strap Is Good For Nothing More Than Holding The Lid On. You Will Want To Buy An Additional Strap If Mounting This Box Externally To A Vehicle Or Trailer. The Price Is What I Though A Plastic Box Should Cost. Many Cost More.

X. Lawrence, Trafford

NOCO HM318BKS GROUP 24-31 SNAP-TOP BATTERY BOX FOR AUTOMOTIVE, MARINE, AND RV BATTERIES Spotlight
Brand :    noco
Color :    Black
Weight :    3.60 pounds
Model :    HM318BKS
Quantity :    1
Order click here :    normally ships in 24 hours
Automotive Parts And Accessories :    Best Auto Accessory (noco) reviews for NOCO HM318BKS Group 24-31 Snap-Top Battery Box for Automotive, Marine, and RV Batteries available as-of ( Sep 2019 )
Unique patented design; Features locking tabs to securely fasten the lid to the base, reinforced handles to prevent cracking during relocation, and vent caps to limit water entryDesigned for rugged environments; Impact resistant down to minus 20 degrees Fahrenheit, withstands acid, gas, oil and other contaminants, and immune to UV exposureCertified and tested; Meets United States Coast Guard (USCG) Code of Federal Regulations 183.420 and American Boat and Yacht Council (ABYC) E-10.7 specificationsKeeps your battery safe; Limits water entry, effectively collects battery acid, allows adequate ventilation, and protects against accidental contact of battery terminalsHeavy-duty grade battery box for Automotive, Marine, RV and more; Designed for a single group 24-31 batteryShips in Certified Frustration-Free Packaging

Camco 47470 Black 5/16" Stud 18" Long 2-Gauge Marine Battery Cable and Lug Assembly Tinned

Camco's 18" 2 Awg 5/16" Stud Premium Marine Quality Battery Cable Wire Is Ul 1426 Listed And Manufactured To The Highest Abyc Standards. Heat-resistant Up To 105c Dry And Available In Black Red And Yellow. Pre-assembled With Premium Marine Quality Tin0plated 95%-copper Lugs Each Strand Of Individually Tinned Wire Provides The Greatest Protection Against Corrosion And Oxidation Available. Camco's Type 3 Boat Cable Wire Stays Ultra Flexible Even In The Most Extreme Conditions.

Camco 47470 Black 5/16" Stud 18" Long 2-Gauge Marine Battery Cable and Lug Assembly Tinned

Camco-47470-2-Gauge-Battery-Assembly

CAMCO 47470 BLACK 5/16" STUD 18" LONG 2-GAUGE MARINE BATTERY CABLE AND LUG ASSEMBLY TINNED Advantages
Brand :    camco
Color :    Black
Size :    18 Inch
Model :    47470
Quantity :    1
Order click here :    normally ships in 24 hours
Automotive Parts And Accessories :    Best Auto Accessory (camco) reviews for Camco 47470 Black 5/16" Stud 18" Long 2-Gauge Marine Battery Cable and Lug Assembly Tinned available as-of ( Sep 2019 )
Heat resistant up to 105C dryUL 1426 listed and manufactured to the highest ABYC standardsTin plated 95% copper lugs for superior corrosion and oxidation resistanceType 3 boat cable wire stays ultra flexible even in the most extreme conditions2 AWG wire, fits 5/16" stud
Blue Sea 9001e E-series Battery Switch (Blue Sea Systems) Price : 33.1, was : 0 as 2017-01-19
USUKDEFRESITJPCNCAGlobal
United States
Great Britain
German
France
Spain
Italy
Japan
China
Canada
World Wide
Blue Sea 9001e E-series Battery Switch (Blue Sea Systems) Reviewed by on jerdus.com

Top blue sea 9001e e-series battery switch (blue sea systems) Content

The F.A.Q. for Blue Sea 9001e E-series Battery Switch (Blue Sea Systems)

Just got my battery switch! the product is very sturdy, with a thick plastic housing. The knob is easily rotated. The terminals for the electrical cables in the back are thick 3/8(10mm) and long 7/8(22mm) stainless steel bolts. There are no exposed components, which is a plus in a marine environment. It is rated 2000 amps for 10 seconds; 1000 amps for one minute, 600 amps for 5 minutes, and 350 amps continuous. Max voltage is 32 volts.

A number of questions have been asked here.

Q&A

(0) Question: if i install it in my car between two batteries the out put termenal , what is wire connect it with it? if i have winch , off road light and stereo?


(1) Question: i want to use this disconnect for my solar panels (not battery bank) 36vdc at 5.25 amps per panel . how many amps will these disconnects handle?


(2) Question: i am upgrading my boat stereo system and will need another battery with an isolator. 1 to start. 1 to jam! is this what i need?


(3) Question: my boat currently has a single battery. is adding a battery as simple as described by kevin (first review)? or was he describing like-kind replacement


(4) Question: ia this product waterproof?


(5) Question: will this separate on grid and off grid inverters? 1000 watt each.


(6) Question: can i use a trickle charger with this battery switch?


(7) Question: how large is the switch? what is the spacing on the mounting holes? thanks!



(note) Question: where/how to get Blue Sea Systems (manufacturer's brand) accessories & similiar Blue Sea Systems's products

Answer:

https://jerdus.com/blue-sea-9001e-battery-switch-507600k2mcr2/

Click the marked text to copy link to Clipboard

These are great switches! they are stout, lightweight, water proof and ultra reliable. I have used several different models over the last 30 years and they are my number one choice. I have ordered one of these 9003e switches for use as a truck winch master power disconnect. I do strongly recommend that all cables have waterproof heat shrink tubing installed, and coat the terminals and cables with "liquid electrical tape" after assembly. . The posted dimensions are incorrect. The actual switch dimensions are 3. 85" x 3. 85" x 3. 1" tall (97. 8 mm x 97. 8 mm x 78. 7 mm tall). . John davies. Spokane wa usa


Bestsellers, Sporting GoodsTop Blue Sea 9001e E-series Battery Switch (Blue Sea Systems) FAQ Content

Best blue sea 9001e e-series battery switch (blue sea systems) in review

I was pleasantly surprised at how easily this unit was to install, kudos to blue sea systems for having excellent nomenclature included with the switch that had very detailed information on mounting options and dimensions for cut-outs and hole centerlines.

B. Mary, Milton Keynes

You might like to see Heated Fleece Travel Electric Blanket - 12 Volt - Red Plaid Auto Accessory Twi 2001
  • Additional: Keeps passengers comfy on long road trips
  • Additional: Measures 58 inch by 42 inch
  • Additional: Constructed from 100 percent high-quality super-soft polyester fleece
heated fleece travel electric blanket - 12 volt - red plaid: trillium worldwide auto accessory trillium worldwide car cozy 2 12-volt heated travel blanket Heated Fleece Travel Electric Blanket - 12 Volt - Red Plaid (Trillium
Or you might like to consider Mr. Funnel Af8cb Fuel Filter Auto Part Af8cb
  1. Reviews: Fast Flow Rate of up to 5.0 gallons per minute for use with portable fuel containers and fuel pumps.
  2. Reviews: REMOVES WATER, Dirt and Debris from Fuel
  3. Reviews: Simple, Portable, and Self-Cleaning
Mr-funnel-af8cb-fuel-filter: Mr Funnel Auto Part The Incredible Mr. Funnel. This Is A Must Have For Anyone Who Stores Fuels. Just Pour The Fuel Through Mr. Funnel Af8cb Fuel Filter (Mr

T. Barbara, West Sussex says

The switch was a breeze to install, feels very solid, and i expect it to last a long time. I'm sure this is a little over-kill for my single marine battery, but i'm willing to pay an extra twenty bucks for peace of mind. This switch has a very high threshold for the load of amps that occur upon starting the engine, and it's size and weight imply that i won't be replacing it any time soon. The ability to flush-mount it worked great and keeps it looking professional. . Regarding my specific setup: i have a standard marine battery running to a 120hp yamaha outboard. For the last couple seasons i have had an issue with the battery dying if i didn't use the boat for several weeks. Physically disconnecting the battery terminals after using the boat solved the problem, but it wasn't the most user-friendly solution for the rest of the family. The issue suggests a larger trickle from the battery than there should be, but it's not worth my time or money to figure out what device is pulling current even when the key is off. So the solution was to get a simple switch that does the same thing as physically disconnecting from the terminals. It's worked great so far; no battery drain after leaving the boat for a month. . Originally i intended to mount it below the dashboard, but i ended up taking more simple route and mounted it closer to the battery in one of the compartments under a back seat. I used a 3 5/8" hole saw to cut through the plastic wall of the seat, about halfway up from the floor. Then i pushed the switch into the hole, marked the four locations of the bolts, drilled four small holes, and mounted the switch with four nuts and bolts. . Note, i needed the following extra materials to install the switch:. 1. 3 5/8" hole saw (not needed unless flush-mounting, and you could use a different tool too). 2. Four bolts and nuts (at least 3. 5" in length, i forget the diameter). 3. Wire and crimp-connectors to extend the wire from the battery to where i mounted the switch, remember that you only need to extend the positive (+) cable to the switch)

Q. Elida, Manitoba

This is a quality product. Works great. Not much else to say. . I use it for my solar projects to disconnect from the batteries.

N. McCarthy, Sachsen-Anhalt says

I don't give out 5 stars (in 1-5 system) often (1st time actually). This is a very high quality battery switch that can mount in the "perko" or "guest" lower amperage switch mounting holes if replacing older equipment. This switch is built to last a lifetime. If you are adding the switch because you want a second battery for backup you can rest assured because that's essentially why i got it (peace of mind in case i used too much juice forgetting to start main motor for charge). The amperage ratings are very good. 2000a/10 sec. 1000a/60 sec. 600a/intermittent 5 min. And 350a/continuous. It's rated for up to 32 volts, and in addition to it's ce/ul/abyc/meeting requirements its ip66 protected against powerful water jets. If you are considering the cheaper switches available, don't, they won't last as long as this one. I had never heard of blue sea before this purchase last week, my review is based on what i received when i ordered this switch and saw the quality i received at an affordable price. There is nothing to dislike, and i would highly recommend (and have) to anyone looking for a battery switch that switches between batteries. If installing new like i am, plan to have room for about a 3 5/8" hole for back mount or 3 7/8" to mount on surface. Holes are designed for 1/4 inch bolts/machine screws.

A. Franklin, Minnesota

This replaced a perko switch that went bad. The perko was not waterproof. The bllue sea cost $7 more but is well worth it. It is waterproof and made much better. I found that any blue sea product i purchase was of very high quality which is important in a marine environment.

G. Ruby, Oklahoma says

Very good

E. Debra, Lorraine

Used it to replace one i accidentally fried. I always loved the very positive click of these switches, you know when you have it engaged thats for sure.

M. Finch, West Virginia says

Good price, fast delivery.

W. Melissa, Mississippi

I did a lot of looking before deciding on this product. Probably like 2 months or more of looking at 10 or more different manufacturers. This this product and the other products from blue sea are ultra high quality and stood out in every way. Look, feel, features, capacity, they even took time to put in little raised nub in this product switch that lets you orient the switch even if its pitch black out. I will buy many more applicable products from blue sea because the quality that they have shown me they are manufacturing is top notch. This switch is such a high quality product that it leaves the competition in the dust, hands down.

F. Guest, Louisiana says

Got this to hook up two batteries on my camper. When it arrived it had no instructions for my intended hookup so i figured out a way to do it. Then i was going to review idea with my friend who is an ee. Then i thought to go to blue sea systems web site for support. I told them what i wanted to do and how i thought i should do it. Emailed them they got right back, told me i was on the right track, and sent me wiring diagram. This switch looks rock solid but it is somewhat open so i will have to think about how to enclose it since i don't think i can just do an unprotected outside mount. I chose this switch because i didn't want the switch that selects batt 1, or 2 or both since both might not work with car and camper charging system that was designed for only one battery

V. Arnett, Virginia

This switch is as it was described. I have only checked it with a meter so far. I will be installing it when my boat come out of storage. I will update my review after it is installed. Switch is now installed and is working great. I used the rear panel mounting option. This means you need to cut a 3-5/8" diameter hole. I installed a 5-1/2" x 3/4" poly plank (available at lowe's) cut to fit a section of my pontoon boat fence. I used a hole saw to cut the hole in the fence and poly plank. The installation looks very professional. The back of the switch is in my engine compartment and will be covered as soon as the non-metallic box i ordered arrives.

A. Delgado, Barnet says

Great device and super-easy to install! this is a very rugged and heavy duty switch! allows switching from one battery or another or both. You can shut power off too to prevent battery drain. I can run my boat radio all day and not be left with the fear of being stranded on the lake.

C. Hakala, Northwest Territries

I installed it on my 2000 sea ray 180 bow rider. I had one 24 series battery and i replaced it with a 27 series and a 31 series, both dual (starting and deep cycle). I used 4 gauge wires from autozone. . 1. Turn off all electronics, put the selector switch on the off position and disconnect all batteries. . 2. When tightening the nuts, make sure they are tight, dc needs to be tight or else there will be problems. . 3. Connect one of the positive wires to terminal one on the back of the switch. . 4. Connect the second positive wire to terminal two on the back of the switch. . 5. Connected the positive from the engine and the positive that comes from the breaker to the common terminal at the bottom of the selector switch. . 6. Mount the switch in the desired location. . 7. Connect the negative of both batteries together and the negative from the engine to a negative terminal of either of the two batteries. . 8. Connect the positive wire from terminal 1 on the switch to the positive terminal on battery 1 (the battery used to start the engine). . 9. Connect the positive wire from terminal 2 on the switch to the positive terminal on battery 2 (the one used for the radio, lights and accessories when the engine is off). . 10. Enjoy having the security of two batteries.



Leave a Reply

You must be logged in to post a comment.


Top blue sea 9001e battery switch Review Content

Related Products

Product Image Gallery

Top-blue-sea-9001e-battery-switch-507600k2mcr2-Content