Ch4x4 Rocker Switch Wrangler Symbol (Ch4x4 Industries) 3135

Review for rocker switch jeep wrangler jk

Price was $15.99. Looks cool

-O. Russell

Ch4x4 rocker switch jeep wrangler jk roof light bar symbol horizontal – these high quality 12 volt rocker switch is a single throw on – off switch designed to operate your 12 volt accessories. they have a face surface size of 2′ (50mm) x 1′ (25mm) and -ch4x4 rocker switch jeep wrangler jk roof light bar symbol horizontal – blue led

  • Plus: Two Leds In The Switch. Upper Led Is On Only When The Switch Is Turned On. Lower Led Is Independent. Both Leds Have Separate Grounds.
  • Plus: Black Hard Surface Rocker. Same Size As The Carling And Arb Switches.

Low-Priced Ch4x4 Rocker Switch Wrangler Symbol (Powersports Vehicle Part)

Buy Now

Prologue

Worked great, fit nicely into the a-pillar pod on my jeep wrangler. The Best rocker switch jeep wrangler jk as-of ( Jul 2018 ) | Ch4x4 Industries-Powersports Vehicle Part Review Plus CH4x4 Rocker Switch Jeep Wrangler JK Roof Light Bar Symbol – Horizontal - Blue LED Single pole single throw on-off switch.. Two leds in the switch. upper led is on only when the switch is turned on. lower led is independent. both leds have separate grounds.. Black hard surface rocker. same size as the carling and arb switches.. Rated 16a 12v.. Wiring diagram supplied with switch. .

Ch4x4 Rocker Switch Jeep Wrangler Jk Roof Light Bar Symbol Horizontal - Blue Led Review (ch4x4 jksrlh b)

Good product and helped me when i needed assistance! -M. Rose

Ch4x4 Rocker Switch Wrangler Symbol

  1. Brand: CH4X4 Industries
  2. Color: Blue
  3. Manufacturer: CH4x4 Industries
  4. Part-Warranty: Parts
  5. MPN: CH4X4-JKSRLH-B
  6. Quantity: 1
  7. Part/Serial Number: CH4X4-JKSRLH-B
  8. Type: Automotive Parts And Accessories
  9. Category: POWERSPORTS VEHICLE PART

ch4x4 rocker switch jeep wrangler jk roof light bar symbol horizontal - Automotive Parts And Accessories, These high quality 12 volt rocker switch is a single throw on - off switch designed to operate your 12 volt accessories. they have a face surface size of 2' (50mm) x 1' (25mm) and uses a standard din size mounting hole of 1. 41' (36mm) x . 86' (22mm) this is the standard size of most switch holes in modern vehicles, however it is best to check your particular hole size if unsure. - all symbols are laser etched directly onto the switch face to ensure long image life. we do not use stickers or ink which will wear off in a very short time. Ch4x4 Rocker Switch Wrangler Symbol (-Ch4x4 Industries).

Ch4x4 Rocker Switch Wrangler Symbol Automotive Parts And Accessories

rocker switch jeep wrangler jk CH4x4 Rocker Switch Jeep Wrangler JK Roof Light Bar Symbol – Horizontal - Blue LED (Switch to Mobile/Desktop Version)

Very nice addition

Ch4x4 Rocker Switch Jeep Wrangler Jk Roof Light Bar Symbol Horizontal - Blue Led
Click to see NoticeCh4x4 Rocker Switch Wrangler Symbol (Ch4x4 Industries)"Classic and perfect. look great in my jeep!"


CH4x4 Rocker Switch Jeep Wrangler JK Windshield Lights Symbol Horizontal - Blue LED

Great switch. works as advertised and planned.

These high quality 12 volt rocker switch is a single throw on - off switch designed to operate your 12 volt accessories. They have a face surface size of 2' (50mm) x 1' (25mm) and uses a standard din size mounting hole of 1. 41' (36mm) x . 86' (22mm) this is the standard size of most switch holes in modern vehicles, however it is best to check your particular hole size if unsure. - all symbols are laser etched directly onto the switch face to ensure long image life. We do not use stickers or ink which will wear off in a very short time.

CH4x4 Rocker Switch Jeep Wrangler JK Windshield Lights Symbol Horizontal - Blue LEDRocker-Switch-Wrangler-Windshield-Lights

Rocker Switch Wrangler Windshield Lights (Ch4x4 Industries) FAQ.

High quality product. This is my 2nd of 4 that i m planning on ordering. -Notice from S. Jarvis, Australian Capital Territory

Click to Show rocker switch wrangler windshield lights (ch4x4 industries) Details

Installed this weekend. Great setup. Jumped the 2 negatives and jumped the dash lights so it's always lit up! sits nicely in the rugged ridge a-pillar switch unit.

Rocker-switch-wrangler-windshield-lights-(ch4x4-industries) set picture

- G. DebraI'm a repeat customer for these switches. Use them with rigid industries light bars and pods. Would only trust great switches with those quality lights. Shipping was fast too.

These switches are great. The green color looks really good in my jeep and it's not too distracting. They were really easy to install and look like they were meant to be there.

L. Glenda, Iowa

CH4X4 ROCKER SWITCH JEEP WRANGLER JK WINDSHIELD LIGHTS SYMBOL HORIZONTAL - BLUE LED Summary
Price :    $15.99
  • Single pole single throw on-off switch.
  • Rated 16a 12v.
  • Two leds in the switch. upper led is on only when the switch is turned on. lower led is independent. both leds have separate grounds.
  • Black hard surface rocker. same size as the carling and arb switches.
  • Wiring diagram supplied with switch.
Brand :    ch4x4 industries
Color :    Blue
Model :    CH4X4-JKSWLH-B
Quantity :    1
Order click here :    normally ships in 2-3 business days
Automotive Parts And Accessories :    Best Powersports Vehicle Part (ch4x4 industries product review) for CH4x4 Rocker Switch Jeep Wrangler JK Windshield Lights Symbol Horizontal - Blue LED available as-of ( Jul 2018 )

Rugged Ridge 17235.56 Black A-Pillar Switch Pod

Looking for a handy place to mount your accessory switches that doesn't require cutting or other modifications? the rugged ridge a-pillar switch pod has premolded cutouts to allow you to mount up to four aftermarket switches in easy reach on the driver's side a-pillar, and out of the way of the shifter handle. Our pillar pod has the textured molded finish just like the factory plastic pillar cover it replaces. It snaps into place just like the oe!

Rugged Ridge 17235.56 Black A-Pillar Switch PodRugged-Ridge-17235-56-Pillar-Switch

RUGGED RIDGE 17235.56 BLACK A-PILLAR SWITCH POD Overview
Brand :    rugged ridge
Color :    Black
Size :    Small Parcel Shipping
Weight :    0..6 pounds
Model :    17235.56
Quantity :    1
Order click here :    normally ships in 24 hours
Automotive Parts And Accessories :    Best Auto Part (Automotive Parts And Accessories product review) for Rugged Ridge 17235.56 Black A-Pillar Switch Pod available as-of ( Jul 2018 )
Price :    $24.99
  • No cutting or other modification
  • Textured gray
  • Premolded cutouts
  • Left hand
  • Easy install

Rugged Ridge 17235.58 Black Left Side A-Pillar 4-Switch Pod

Item Sold As "made For" 2015 Wrangler Among Other Years. Extensive Craving Required To Install And Them Fit Was Poor. I Removed It And Threw It Away! Went Online To Try To Find Phone Number For Rugged Ridge To Provide Feedback And Site Has No Numbers. Wonder Why

Looking for a handy place to mount your accessory switches that doesn't require cutting or other modifications? the rugged ridge a-pillar switch pod has premolded cutouts to allow you to mount up to four aftermarket switches in easy reach on the driver's side a-pillar, and out of the way of the shifter handle. Our pillar pod has the textured molded finish just like the factory plastic pillar cover it replaces. It snaps into place just like the oe!

Rugged Ridge 17235.58 Black Left Side A-Pillar 4-Switch PodRugged-Ridge-17235-58-Pillar-4-Switch

Rugged Ridge 17235.58 Black Left Side A-pillar 4-switch Pod (Auto Part) FAQ.

I Purchased This Product To Have An Easier Install Of A Switch After Installing Some Kc Hilites. Install Time Took 1 Hour Tops For Someone Who Does Not Work On Cars That Often. It Involved Removing The Two Panels On The Left. For The Price It Is Alright. I Was Pretty Disappointed When I Was Installing This Piece And The Plastic Fastener Broke Off Really Easily. I Was Still Managed To Install It But I'm Pretty Disappointed How Flimsy Quality The Material Is. Also I Did Not Like How I Had To Take Off A Metal Fastener From The Tailgate Since This Product Did Not Come With Some Already. For My 2011 Jeep Wrangler The Product Did Not Fit As Snug And Nicely As The Factory Panel It Is Replacing. For This Reason I'm Only Giving It Three Stars. I Only Installed One Switch On It But I Feel Like If I Want To Install More Later On The Plastic Fastener Will Break To The Point Where It Is Unusable When I Take If Off. Pros: Looks Nice Custom Cut To Fit Needs Oem Style Finish Price Cons: Does Not Have A Secure Fit Plastic Fasteners Are Flimsy Does Not Come With Metal Fasteners -Notice from A. Clara, Limousin

Click to Show rugged ridge 17235.58 black left side a-pillar 4-switch pod (auto part) Details

Love This Looks Great Easy To Install. 2nd One That I Have Purchased For My Jku. With This One I Colored Outside Of The Lines And Mounted 8 3/4" Round Switches Also Purchased From Online Store So That I Could Up My Light Count

Rugged-ridge-17235.58-black-left-side-a-pillar-4-switch-pod-(auto-part) set picture

- V. NancyI Bought This For My Light Switches In My 2013 Wrangler. The Fit Is Very Good & The Texture Finish Isnt Completly The Same As The Stock A-pillar But It Is Very Close. Its Not Bad Enough To Bother Me & Im Pretty Picky About What I Put On My Jeep. Looks Good Holds My Switches & Doesnt Cost Too Much. What More Could You Ask For.

First You Have To Manually Cut All The Holes For The Switches And You Better Be Good With A Knife Or Have A Dremel Tool To Get The Cuts Correct. Even With Knife Skills Or A Dremel If You Make The Slightest Mistake Your Switches Will Be Misaligned/unevenly Spaced And Will Look Crappy. I Thought It Had Pre-cut Holes With Rectangular Snap In Panels To Cover The Opening If You Have Less Than 4 Switches. Second The Instructions Have You Remove A Part From The Tailgate So That You Can Rob A Metal Clip From That Trim Piece To Use On This Product. All This So They Can Save 50 Cents On A Metal Clip That Should Be Included With This Product. Third The The Left Edge Of The Product Does Not Properly Align With The A-pillar Door Seam So It Does Not Fit Like The Oem Part You Remove.

I. Lara, South Australia

RUGGED RIDGE 17235.58 BLACK LEFT SIDE A-PILLAR 4-SWITCH POD Pros
Price :    $14.69 (was $24.99)
  • Easy install
  • No cutting or other modification
  • Premolded cutouts
  • Black
  • Left hand
Brand :    rugged ridge
Color :    Black
Weight :    0..6 pounds
Model :    17235.58
Quantity :    1
Order click here :    normally ships in 24 hours
Automotive Parts And Accessories :    Best Auto Part (Automotive Parts And Accessories product review) for Rugged Ridge 17235.58 Black Left Side A-Pillar 4-Switch Pod available as-of ( Jul 2018 )

Jeep JK Control Box - Electronic 6 Relay System Module - Wiring Harness Kit With FREE 4 Rocker Switch Mount - Power up to 6 Accessories LED Off Road Light Bars Jeep Wrangler JK Version

Sui-system - suitech's universal relay system - unable to provide power to your aftermarket lights? - tired of buying multiple components just to run into more wiring issues? - need a simple wiring solution that will perfectly fit your wrangler? look no more! your all-in-one wiring solution is here! at suitech we've engineered an all-in-one wiring system solution. Properly wiring your aftermarket lights is important to avoid fires or warranty issues. We've done the homework for you so you can spend more time building your vehicle, and less time worrying about technical issues. Instructions are downloadable below. Simple design - system requires no modifications. Installation takes only 1 hour. - wiring system includes fuses and relays to protect your aftermarket lights. - fits nicely under the hood. - operating voltage: 12v. Max wattage: 600 watts. - integrated temperature protection. Protects lights from overheating warranty information: - we've manufactured thousands of lights! we know what it takes to power them properly. - you will love this system or your money back! - one (1) year replacement. - contact tejera llc to redeem warranty. Included: - one (1) 4 switch a-pillar (driver side). - four (4) rocker switches (2 blue/ 2 red). - one (1) control box with wiring. - one (1) bracket. - one (1) 6-terminal block with hardware. - wiring instruction. We can only guarantee this special pricing while supply last. Buy now!

Jeep JK Control Box - Electronic 6 Relay System Module - Wiring Harness Kit With FREE 4 Rocker Switch Mount - Power up to 6 Accessories LED Off Road Light Bars Jeep Wrangler JK VersionJeep-Control-Box-Electronic-Accessories

JEEP JK CONTROL BOX - ELECTRONIC 6 RELAY SYSTEM MODULE - WIRING HARNESS KIT WITH FREE 4 ROCKER SWITCH MOUNT - POWER UP TO 6 ACCESSORIES LED OFF ROAD LIGHT BARS JEEP WRANGLER JK VERSION Highlight
Price :    $149.95 (was $199.99)
  • No modifications required: designed for your ultimate convenience, this wiring kit has everything you need for installation and use. each box includes a 6-switch panel, circuit control box, wires and hardware.
  • Quick, easy installation: in just an hour, you can be ready to show off those custom lights. with plug and play wiring and easy-to-install components, set-up is quick and hassle-free.
  • Universal compatibility: our patent pending circuit is a must-have for controlling your custom lights and accessories, this all-in-one universal wiring system is compatible with virtually any vehicle and eliminates the need for multiple components.
  • Protects your custom lights: an integrated temperature protection system enables you to safely power all connected lights. the fuses and relays are designed to prevent overheating and protect your investment.
  • Power up to 6 aftermarket lights and accessories: operating at 12 volts and a max power rating of 600 watts, this 6 switch electronic relay module provides ample power for your custom set up.
Brand :    suitech
Color :    Black Relay Box (Jeep Wrangler JK)
Size :    Jeep Wrangler JK Version
Model :    SUI-CTRL-SYSTM
Quantity :    1
Order click here :    normally ships in 24 hours
Automotive Parts And Accessories :    Best Auto Part (suitech product review) for Jeep JK Control Box - Electronic 6 Relay System Module - Wiring Harness Kit With FREE 4 Rocker Switch Mount - Power up to 6 Accessories LED Off Road Light Bars Jeep Wrangler JK Version available as-of ( Jul 2018 )

AntennaX Off-Road 13-inch Antenna 07 thru 18 Jeep Wrangler JK JL

My '07 jk unlimited never had good reception; but i finally got around to fixing it recently. I pulled the center dash panel (good instructions can be found all over the forum), and popped the radio first to check all the connections. After disconnecting and cleaning all the connections i found that the performance was the same - local stations were not receiving in stereo, distant stations were buried in static, and seek didn't find much - even among my presets. With some consideration - i tried isolating the radio, by grounding it with a harness directly to a frame connection in the forward cabin firewall - but this didn't have much (if any effect). . I decided to try removing and cleaning the antenna. Along the way i traced the wire and verified no critters had been snacking on it and that it was making a good connection throughout - well, i lost the chase as it passed through the firewall, but it was good that far, and i took the rest on faith. I removed, cleaned, lightly sanded the rod, brushed the connector points with a stainless brush, added a little conductive sealant on top of the connector, threadlocked the threads and yanked it tight. All great for practice, but it didn't help - at all. No change. At this point, i was pretty sure i had a dud radio - but i thought i'd take the opportunity to tinker. I noticed (according to my jk's compass) that when running n/s routes reception was better than on e/w routes - so i figured it should have something to do with the antenna position or cable path, causing a blind spot during e/w-w/e travel. It wasn't a big difference, but it was a needling concern over 10 years of ownership. I decided that a good course could be to replace the antenna and cable with a new setup - to see if that helped at all. I ordered this one: url " and i also got a url "https://smile. Online store. Com/gp/product/b00651clcs/ref oh aui search detailpage? ie utf8&psc 1" rubber ducky /url to replace the whip outside. I first installed the whip, knowing that it wouldn't help (but at the same time knowing i've never trusted a stainless whip as an antenna anyway). It didn't help. Nor did installing the new antenna and cable! . Well, not until i monkeyed with the installation some (more than some, but not a lot). With the dash still open, i tried a couple a placements for the antenna - along the rollcage horizontal top supports. Down the passenger and the driver side was less than stellar performance, and the cable isn't long enough to reach the center of my unlimited rig. I ended up with the best performance when i put the antenna over the dash inside the plastic cowling along the top of the windshield. I directed the cable through the cowling over the passenger sun visor - and down the inner cowling of the windshield vertical support. From there i entered the dash and used zip ties to route it over the glove compartment and keep it tucked away - then into the center dash compartment from behind the dash. By manipulating it an playing with the routing, i found that crossing the glove compartment straight across, then turning the cable at a 90 degree angle to the front of the compartment, and around the radio installation support frame, behind the radio compartment and into the back of the radio. If you're not careful about that cable path it may cause some issues. I found that it's also important to get the cable connector on the antenna cable clear of the other wires and harnesses in the compartment as well - move the connector up behind the radio in the front portion of the dash for the best performance. Now the radio works great - i get all the local stations in full stereo, many distant stations, and even catch some dx when the weather is right. I still notice some deleterious effects when the weather is heavy in my area, but we are mountainous - so it's not unexpected. Overall, i would gauge this as at least a 500% improvement in reception. That's estimated, not based on empirical analysis. I strongly recommend this configuration and the products i have mentioned. I hope you have as much good luck as i did - and enjoy the ride! (i enjoy it a little more with some great tunes to blare when it's time to go topless! )

Replace your ugly factory (31 inch) metal shaft antenna with this stylish yet functional low profile (13 inch) flexible rubber antenna that will not hit the garage door anymore! if you are unsure that it fits, try unscrewing the existing antenna mast off. If it twists right off, then this antenna will fit since it comes with vehicle specific adapters (no two antennas are the same fit). Installation is very simple. This is a plug-n-play antenna, which means it screws onto your existing antenna mount (a direct bolt-on part, no wiring involved) and takes a minute to do. Most people wonder about losing reception with this antenna. 99. 9% of the time reception stays the same or improves. This antenna replaces your stock am/fm radio antenna and does not affect on-star, bluetooth, gps navigation, or sirius xm radio as those satellite services use a separate antenna in your vehicle. This compact high quality black matte finish rubber antenna cleans up the appearance of the front or rear of your car and is an extremely durable upgrade from any stock antenna. A great improvement for little money and effort!

AntennaX Off-Road 13-inch Antenna 07 thru 18 Jeep Wrangler JK JLAntennaX-Off-Road-13-inch-Antenna-Wrangler

Antennax Off-road 13-inch Antenna 07 Thru 16 Jeep Wrangler Jk (a1j jep17) FAQ.

If your antennax won't screw all the way onto your wrangler jk (mine wouldn't and i have a 2014) here's the fix: (1) unscrew the bottom 2-inch segment of the antennax. (2) remove the threaded rod inside this segment. (3) screw the bottom 2-inch segment onto your jeep. It will now go on all the way. (4) screw the small threaded rod into the top of the bottom 2-inch segment as far as it will go. (5) screw the antenna onto the threaded rod that is sticking out of the bottom segment. Done! what kept the antennax from screwing fully onto your jeep was the short threaded coupler inside. Hope that clarifies. -Notice from B. Sarah, Indiana

Click to Show antennax off-road 13-inch antenna 07 thru 16 jeep wrangler jk (a1j jep17) Details

I hated the stock factory antenna on my wrangler. I had a hard time deciding between this one the 13" and the small stubby 6" one. I'm glad my husband talked me into this one it really looks so much better than the gigantic silver one. Really for such a small price it makes a huge deal!

Antennax-off-road-13-inch-antenna-07-thru-16-jeep-wrangler-jk-(a1j-jep17) set picture

- N. LawrenceAs soon as i put this on my 2012 rubicon jk the stations that used to get bad receptions in locations that were known to be spotty for cell service in my town never once had static. I read reviews before i bought this and i saw a lot of people didn't think it helped. I don't know. My speakers sound like hd now after putting this on. Also, i noticed some people say they twisted the antenna a little too hard into the receiver, so i made sure to slowly turn it in and tighten it. Not sure that made a difference, but i also have a friend who bought a new unlimted jk and he experienced the same positive results. Wonder if its just the locartion of where some people live or turning and twisting the antenna too tight. Either way i love it.

Very cool "upgrade" that really looks much better. It's one of those things that you don't really notice how much better the jeep looks with this until it's on. . Pros - inexpensive and it looks great. Cons - maybe it's just me, but the reception seems to be a little less than what the stock one was. That being said, regular radio is basically not even used with me (sirius/xm and bluetooth satisfy me).

R. Rose, Newfoundland and Labrador

ANTENNAX OFF-ROAD 13-INCH ANTENNA 07 THRU 18 JEEP WRANGLER JK JL Benefits
Brand :    antennax
Weight :    0.10 pounds
Model :    A1J-JEP17
Quantity :    1
Order click here :    normally ships in 24 hours
Automotive Parts And Accessories :    Best Auto Part (antennax product review) for AntennaX Off-Road 13-inch Antenna 07 thru 18 Jeep Wrangler JK JL available as-of ( Jul 2018 )
Price :    $16.99
  • 99. 9% of the time reception stays the same or improves
  • Fits 2007 thru 2018 jeep wrangler jk & jl
  • Does not affect on-star, bluetooth, gps navigation, or sirius xm radio as those satellite services use a separate antenna in your vehicle
  • Replace your ugly factory (31 inch) metal shaft antenna with this stylish yet functional low profile (13 inch) flexible rubber antenna
  • Plug-n-play installation, which means it screws onto your existing antenna mount (a direct bolt-on part, no wiring involved) and takes a minute to do

CH4x4 Rocker Switch Jeep Wrangler JK Bumper Lights Symbol - Horizontal - Blue LED

These high quality 12 volt rocker switch is a single throw on - off switch designed to operate your 12 volt accessories. They have a face surface size of 2' (50mm) x 1' (25mm) and uses a standard din size mounting hole of 1. 41' (36mm) x . 86' (22mm) this is the standard size of most switch holes in modern vehicles, however it is best to check your particular hole size if unsure. - all symbols are laser etched directly onto the switch face to ensure long image life. We do not use stickers or ink which will wear off in a very short time.

CH4x4 Rocker Switch Jeep Wrangler JK Bumper Lights Symbol - Horizontal - Blue LEDRocker-Switch-Wrangler-Bumper-Lights

CH4X4 ROCKER SWITCH JEEP WRANGLER JK BUMPER LIGHTS SYMBOL - HORIZONTAL - BLUE LED Pros
Brand :    ch4x4 industries
Color :    Blue
  • Two leds in the switch. upper led is on only when the switch is turned on. lower led is independent. both leds have separate grounds.
  • Black hard surface rocker. same size as the carling and arb switches.
  • Wiring diagram supplied with switch.
  • Single pole single throw on-off switch.
  • Rated 16a 12v.
Price :    $15.99
Model :    CH4X4-JKSBLH-B
Quantity :    1
Order click here :    normally ships in 2-3 business days
Automotive Parts And Accessories :    Best Powersports Vehicle Part (ch4x4 industries product review) for CH4x4 Rocker Switch Jeep Wrangler JK Bumper Lights Symbol - Horizontal - Blue LED available as-of ( Jul 2018 )

CH4x4 Rocker Switch Jeep Wrangler JK Rear Lights Symbol Horizontal - Blue LED

These high quality 12 volt rocker switch is a single throw on - off switch designed to operate your 12 volt accessories. They have a face surface size of 2' (50mm) x 1' (25mm) and uses a standard din size mounting hole of 1. 41' (36mm) x . 86' (22mm) this is the standard size of most switch holes in modern vehicles, however it is best to check your particular hole size if unsure. - all symbols are laser etched directly onto the switch face to ensure long image life. We do not use stickers or ink which will wear off in a very short time.

CH4x4 Rocker Switch Jeep Wrangler JK Rear Lights Symbol Horizontal - Blue LEDRocker-Switch-Wrangler-Lights-Symbol

CH4X4 ROCKER SWITCH JEEP WRANGLER JK REAR LIGHTS SYMBOL HORIZONTAL - BLUE LED Reviews
Price :    $15.99
  • Wiring diagram supplied with switch.
  • Black hard surface rocker. same size as the carling and arb switches.
  • Two leds in the switch. upper led is on only when the switch is turned on. lower led is independent. both leds have separate grounds.
  • Rated 16a 12v.
  • Single pole single throw on-off switch.
Brand :    ch4x4 industries
Color :    Blue
Model :    CH4X4-JKSRH-B
Quantity :    1
Order click here :    normally ships in 2-3 business days
Automotive Parts And Accessories :    Best Powersports Vehicle Part (ch4x4 industries product review) for CH4x4 Rocker Switch Jeep Wrangler JK Rear Lights Symbol Horizontal - Blue LED available as-of ( Jul 2018 )

CH4x4 Rocker Switch Zombie Lights Symbol Horizontal - Blue LED

These high quality 12 volt rocker switch is a single throw on - off switch designed to operate your 12 volt accessories. They have a face surface size of 2' (50mm) x 1' (25mm) and uses a standard din size mounting hole of 1. 41' (36mm) x . 86' (22mm) this is the standard size of most switch holes in modern vehicles, however it is best to check your particular hole size if unsure. - all symbols are laser etched directly onto the switch face to ensure long image life. We do not use stickers or ink which will wear off in a very short time.

CH4x4 Rocker Switch Zombie Lights Symbol Horizontal - Blue LEDRocker-Switch-Zombie-Lights-Symbol

CH4X4 ROCKER SWITCH ZOMBIE LIGHTS SYMBOL HORIZONTAL - BLUE LED Highlight
Brand :    ch4x4 industries
Color :    Blue
  • Black hard surface rocker. same size as the carling and arb switches.
  • Single pole single throw on-off switch.
  • Rated 16a 12v.
  • Two leds in the switch. upper led is on only when the switch is turned on. lower led is independent. both leds have separate grounds.
  • Wiring diagram supplied with switch.
Price :    $15.99
Model :    CH4X4-ZOMBH-B
Quantity :    1
Order click here :    normally ships in 2-3 business days
Automotive Parts And Accessories :    Best Powersports Vehicle Part (ch4x4 industries product review) for CH4x4 Rocker Switch Zombie Lights Symbol Horizontal - Blue LED available as-of ( Jul 2018 )

2011 2012 2013 2014 2015 2016 2017 Jeep Wrangler JK/JKU A-Pillar Switch Panel Pod

The led switch pod is designed to install on to your a-pillar and allow for four (4) led switches to control the equipment of your choice. Made for jk wranglers and easily installed. Uses factory hardware. The switches made to fit are black mountain rocker switch bmrs-g (green) bmrs-b (blue) bmrs-r (red) bmrs-a (amber)

2011 2012 2013 2014 2015 2016 2017 Jeep Wrangler JK/JKU A-Pillar Switch Panel Pod2011-Wrangler-Pillar-Switch-Panel

2011 2012 2013 2014 2015 2016 2017 JEEP WRANGLER JK/JKU A-PILLAR SWITCH PANEL POD Reviews
Brand :    black mountain
Model :    BMSP
Quantity :    1
Order click here :    normally ships in 1-2 business days
Automotive Parts And Accessories :    Best Auto Accessory (black mountain product review) for 2011 2012 2013 2014 2015 2016 2017 Jeep Wrangler JK/JKU A-Pillar Switch Panel Pod available as-of ( Jul 2018 )
Price :    $44.51 (was $44.74)
  • Easy to use
  • Fits 2011-2017 jeep wrangler
  • Nice look to your switches
  • Switches sold seperate
  • Easy install

Opar Black US American Flag Gas Cap Gas Tank Cover 2007-2018 Jeep JK Wrangler & Wrangler Unlimited JK

Use it to add some style and attitude to your jeep these easily fit and giving your exterior that custom look in minutes opar offers the best in quality products for all your jeep exterior needs package included: -1 x opar jeep wrangler gas cap opar is a registered us brand which started by ian in 2013. With a background in jeeping for more than 5 years. At opar our goal is to make your jeeping experience the absolute best that it could be. The main thing is that we install everything we sell. Not only are our products used on our very own jeeps, but we have also tested almost everything that we sell on the road and in the field. Always buy with confidence since opar offers 2 years warranty on most of opar branded products

Opar Black US American Flag Gas Cap Gas Tank Cover 2007-2018 Jeep JK Wrangler & Wrangler Unlimited JKopar-American-2007-2018-Wrangler-Unlimited

OPAR BLACK US AMERICAN FLAG GAS CAP GAS TANK COVER 2007-2018 JEEP JK WRANGLER & WRANGLER UNLIMITED JK Reviews
Price :    —
  • Easy to install, no drilling required, non-locking, smooth door operation, and anti-corrosion finish
  • Package detail: 1 x opar jeep wrangler gas cap
  • Made of aluminum & abs materiral, resistant to gasoline and other hazardous chemicals
  • It gives your jeep wrangler a sporty look by adding a unique heavy duty fuel filler door
  • Fits for 2007-2018 jeep wrangler & wrangler unlimited jk
Brand :    opar
Model :    LED-3023NW
Quantity :    1
Order click here :    -
Automotive Parts And Accessories :    Best Auto Accessory (opar product review) for Opar Black US American Flag Gas Cap Gas Tank Cover 2007-2018 Jeep JK Wrangler & Wrangler Unlimited JK available as-of ( Jul 2018 )

ch4x4 rocker switch jeep wrangler jk roof light bar symbol horizontal - blue led Price : 15.99, was : 0 as 2018-06-26
USUKDEFRESITJPCNCAGlobal
United States
Great Britain
German
France
Spain
Italy
Japan
China
Canada
World Wide
Ch4x4 Rocker Switch Wrangler Symbol (Ch4x4 Industries) Reviewed by on jerdus.com

Top ch4x4 rocker switch wrangler symbol (ch4x4 industries) Content

The F.A.Q. for ch4x4 rocker switch jeep wrangler jk roof light bar symbol horizontal - blue led

Fits great into the a-pillar column, looks sexy, not too bright.

A number of questions have been asked here.

Q&A

(0) Question: do you offer this switch as is with the word led instead of light?



(note) Question: where/how to get Ch4x4 Industries (manufacturer's brand) accessories & similiar Ch4x4 Industries's products


Automotive 18148651, Electrical 110127404, Motorcycle & Powersports 110333643, Parts 110956404, Switches 110427404Top Ch4x4 Rocker Switch Wrangler Symbol (Ch4x4 Industries) FAQ Content

Best ch4x4 rocker switch wrangler symbol (ch4x4 industries) in review

Love it, great product. Switch moves smoothly but won't be nudged on accedent. Great brightness on led's, easy to follow connector diagram.

Z. Claudia, Pennsylvania

You might like to see Ch4x4 rocker switch jeep wrangler jk windshield lights symbol horizontal - these high quality 12 volt rocker switch is a single throw on - off switch designed to operate your 12 volt accessories. they have a face surface size of 2' (50mm) x 1' (25mm) and -ch4x4 rocker switch jeep wrangler jk windshield lights symbol horizontal - blue led
  • Additional: Two Leds In The Switch. Upper Led Is On Only When The Switch Is Turned On. Lower Led Is Independent. Both Leds Have Separate Grounds.
  • Additional: Black Hard Surface Rocker. Same Size As The Carling And Arb Switches.
Affordable Rocker Switch Wrangler Windshield Lights (Powersports Vehicle Part) Rocker Switch Wrangler Windshield Lights (Ch4x4
Or you might like to consider Nickel Anti-seize Lubricant, 8 Permatex Nickel Anti-seize Lubricant Protects Metal Parts From Seizing And Galling At Temperatures Up To 2400 Degrees Fahrenheit. Copper-free, This Lubricant Is For Use Under Conditions -Permatex 77124 Nickel Anti-seize Lubricant, 8 Oz.
  1. Spotlight: For Use With Stainless Steel, Titanium And Nickel Alloys.
  2. Spotlight: For Use Under Conditions Of Extreme Pressure And Temperature.
Most Wishlist Permatex 77124 Nickel Anti-seize Lubricant, 8 Oz. (Auto Accessory) 77124 Permatex 77124 Nickel Anti-seize Lubricant, 8 Oz. (Auto

K. Connie, Manitoba says

Easy install

E. Pearson, Sachsen

Great!

V. Carolyn, Maryland says

Great product works as expected.

B. Gloria, Alsace

Worked great exactly as it should. Easy to follow diagram. Looks really cool

N. Mathis, Haringey says

Great rocker switch! nice and snug when installed, looks great with the lights on and had very clear wiring instructions on the back of the package. Would definitely recommend this product.

B. Cassella, Quebec

The look and quality of the switch is great

D. Isabel, Leeds says

Looks amazing! fits nice in my a pillar switch box

U. Kristen, Barnsley

Looks great! works fine. would recommend.

L. Crawford, Southwark says

Look great good quality

P. Alberta, Bayern

Great product. My only complaint and the reason i gave them four stars instead of five is the rock is wider then the switch base. When installed in an a pillar switch mount, the sides of the switches run against each other. Would be nice if the design was changed so the switches could be snugged together without the rockers touching.

N. Wanda, Trafford says

Easy install

D. Marguerite, Slough

Awesome product!



Leave a Reply

You must be logged in to post a comment.


Top rocker switch jeep wrangler jk Review Content

Related Products

Product Image Gallery

Top-ch4x4-rocker-switch-wrangler-symbol-31350uudzdng-Content