J-b Weld 8265s Original Steel Reinforced Epoxy Twin Pack – 2 Oz (pack Of 2) (J B Weld) 4174

Review for j b weld 8265s original reinforced

Price was $11.50. Works well for many purposes.

-Z. Shawna

J-b Weld 8265s Original Steel Reinforced Epoxy Twin Pack – 2 Oz (pack Of 2) Auto Accessory

  1. Products: Non Toxic formula
  2. Products: Use on automotive, brick, concrete, metal and more
  3. Products: Easy to use, cures to dark gray

J-b-weld-8265s-original-reinforced: J B Weld Auto Accessory J-b Weld Is The Original Cold Weld Two-part Epoxy System That Provides Strong Lasting Repairs

Buy Now

Non Toxic Formula, Easy To Use, Cures To Dark Gray, Use On Automotive, Brick, Concrete, Metal And More, Will Set In 4-6 Hours, And Cure In 16-24 Hours, Waterproof, Petroleum, Chemical, And Acid Resistant When Fully Cured, Products J-B Weld 8265S Original Steel Reinforced Epoxy Twin Pack - 2 oz (Pack of 2).

Ingredients: J-b Weld 8265s Original Steel Reinforced Epoxy Twin Pack - 2 Oz (pack Of 2)

J-b Weld 8265s Original Steel Reinforced Epoxy Twin Pack - 2 Oz (pack Of 2) Half Price Automotive Parts And Accessories J B Weld, J-b Weld 8265s Original Steel Reinforced Epoxy Twin Pack - 2 Oz (pack Of 2) 7091267059903. j-b weld is the original cold weld two-part epoxy system that provides strong lasting repairs to metal and multiple surfaces. mixed at a ratio of 1:1 it forms a permanent bond and can be shaped tapped filed sanded and drilled after curing. at room temperature j-b weld sets in 4-6 hours to a dark grey color. a full cure is reached in 15-24 hours. j-b weld has a tensile strength of 3960 psi and sets to a hard bond overnight. it can withstand temperatures up to 550f when fully cured. J-b Weld 8265s Original Steel Reinforced Epoxy Twin Pack - 2 Oz (pack Of 2) Auto Accessory.

J-B Weld 8265S Original Steel Reinforced Epoxy Twin Pack - 2 oz (Pack of 2) Overview (8265-S)

J-b Weld 8265s Original Steel Reinforced Epoxy Twin Pack - 2 Oz (pack Of 2)

  • Brand : J-B Weld
  • ClothingSize : 2-Pack
  • EAN : 7091267059903
  • Manufacturer : J-B Weld
  • ManufacturerPartsWarrantyDescription : Parts
  • MPN : 8265-S
  • Quantity : 2
  • Part Number : 8265-S
  • Group : Automotive Parts And Accessories
  • Category : AUTO ACCESSORY
  • Size : 2-Pack
  • Title : J-B Weld 8265S Original Steel Reinforced Epoxy Twin Pack - 2 Oz (Pack Of 2)

Ingredients J-b-weld-8265s-original-reinforced

J B Weld : J-B Weld 8265S Original Steel Reinforced Epoxy Twin Pack - 2 oz (Pack of 2)

  • Non Toxic Formula
  • J-B Weld 8276 KwikWeld Quick Setting Steel Reinforced Epoxy - 2 Oz, Pack Of 2
  • J-B Weld 8281 Professional Size Steel Reinforced Epoxy Twin Pack - 10 Oz
  • J-B Weld 8267-S SteelStik Steel Reinforced Epoxy Putty Stick - 2 Oz
  • J-B Weld 8276 KwikWeld Quick Setting Steel Reinforced Epoxy - 2 Oz
  • J-B Weld 50101 MinuteWeld Instant-Setting Epoxy Syringe - Dries Clear - 25ml
  • Lisle 34550 Handy Packer Bearing Packer
  • Milton S-153 1/4" NPT Lever Style Blow Gun
  • 3M 32035 Imperial Wetordry 9" X 11" P800 Grit Sheet
  • Use On Automotive, Brick, Concrete, Metal And More
  • Easy To Use, Cures To Dark Gray
Best Price

I have bought many packs of this epoxy to use on a variety of repairs. It is an excellent product and as long as you give it a good prepped surface and a long drying time, this bond is nearly permanent. There is only one issue that i have experienced three times with this product, the first issue i had was a tube actually broke open on the side. Granted the tube was a couple years old and fairly worn so i just thought it was normal wear an tear. Then recently i have used the epoxy more and in the last few months have purchased three packs of the epoxy. Out of those three packs i bought, two of them ended up having the caps of the tubed crack open and ooze epoxy out of them into my tool box. Online store was great at replacement of them but the fact that two of them broke open when only used a few times is annoying.

j-b-weld-8265s-original-reinforced
Click to see NoticeJ-b Weld 8265s Original Steel Reinforced Epoxy Twin Pack - 2 Oz (pack Of 2) (J B Weld)"So glad i bought this to repair a ceramic birdbath. The piece attached to the bottom of the bowl, which locks into the pedestal, had broken off the bowl. It was pushed to the limit because i tilt the bowl (while attached to the pedestal) in order to dump the dirty water. The two surfaces to be adhered were both rough textures and had probably originally been cemented. Three weeks after repairing with j-b weld, the birdbath is still holding even though i continue to empty the water the same way. I allowed the bonded pieces to set over 12 hours before placing the bowl back into the pedestal."

J-B Weld 8276 KwikWeld Quick Setting Steel Reinforced Epoxy - 2 oz

J-b Weld Kwikweld Quick Setting Steel Reinforced Epoxyj-b Kwikweld Is A Fast Setting Version Of The Original J-b Weld Two-part Epoxy Cold Weld System That Provides Strong Lasting Repairs To Metal And Multiple Other Surface Types. After Mixing It Forms A Permanent Bond And Can Be Shaped Tapped Filed Sanded And Drilled After Curing. J-b Kwikweld Has A 1:1 Mixing Ratio Sets In 6 Minutes And Is Fully Cured In 4-6 Hours. J-b Kwikweld Cures To A Dark Grey Color Is Rated At A Tensile Strength Of 2424 Psi And Will Withstand Temperatures Up To 300 Degrees F. Great For:household Repairsautomotiveplumbingmarinecrafts And Moreuse On:automotivebrickconcretefiberglassmetaland Moreinstructions1. Prepare: Clean Surface Area Of Dirt Grease Oil Paint Or Loose Debris. For Best Results Use A Detergent Or Degreaser To First Clean The Surface Then Roughen Surface With File Or Coarse Sandpaper To Provide The Best Repair. 2. Mix: Squeeze Equal Parts From Each Tube Onto A Disposable Surface And Mix Thoroughly. 3. Apply: Apply With Appropriate Tool In An Even Coat Weld Bead Or Extruded Shape As Needed. 4. Dry: Sets In 6 Minutes. Cures 4 Hours. If Temperature Is Below 40 Degrees F Then Set Time Is Longer. J-b Weld Is Proudly Made In The Usa

J-B Weld 8276 KwikWeld Quick Setting Steel Reinforced Epoxy - 2 oz

J-B-Weld-8276-KwikWeld-Reinforced

J-B WELD 8276 KWIKWELD QUICK SETTING STEEL REINFORCED EPOXY - 2 OZ Review
Brand :    j-b weld
Color :    White
Size :    2 oz
Weight :    0.5 pounds
Model :    8276
Quantity :    1
Order click here :    normally ships in 24 hours
Automotive Parts And Accessories :    Best Auto Accessory (Automotive Parts And Accessories) reviews for J-B Weld 8276 KwikWeld Quick Setting Steel Reinforced Epoxy - 2 oz available as-of ( Oct 2019 )
Sets in 6 minutes and cures dark grey in 4-6 hoursGreat for household repairs, automotive applications, crafts and moreFast setting version of The Original J-B Weld two-part epoxy cold weld systemWill withstand temperatures of up to 300 degrees FahrenheitRated at a tensile strength of 2424 PSIOnce cured it forms a permanent bond and can be shaped, tapped, filed, sanded and drilled

J-B Weld 8281 Professional Size Steel Reinforced Epoxy Twin Pack - 10 oz

J-b Weld Original Cold-weld Formula Steel Reinforced Epoxyj-b Weld Is The Original Cold Weld Two-part Epoxy System That Provides Strong Lasting Repairs To Metal And Multiple Surfaces. Mixed At A Ratio Of 1:1 It Forms A Permanent Bond And Can Be Shaped Tapped Filed Sanded And Drilled After Curing. At Room Temperature J-b Weld Sets In 4-6 Hours To A Dark Grey Color. A Full Cure Is Reached In 15-24 Hours. J-b Weld Has A Tensile Strength Of 3960 Psi And Sets To A Hard Bond Overnight. It Can Withstand Temperatures Up To 550f When Fully Cured. Use On:automotivebrickconcreteepoxy And Adhesivesfiberglassmetaland Moreinstructions1. Prepare: Clean Surface Area Of Dirt Grease Oil Paint Or Loose Debris. For Best Results Use A Detergent Or Degreaser To First Clean The Surface Then Roughen Surface With File Or Coarse Sandpaper To Provide The Best Repair. 2. Mix: Squeeze Equal Parts From Each Tube Onto A Disposable Surface And Mix Thoroughly. 3. Apply: Apply With Appropriate Tool In An Even Coat Weld Bead Or Extruded Shape As Needed. 4. Dry: Sets In 4-6 Hours. Cures In 15-24 Hours. Allow 4-6 Hours Before Handling And 15 Hours (minimum) Before Putting Object Back In Use. J-b Weld Is Proudly Made In The Usa

J-B Weld 8281 Professional Size Steel Reinforced Epoxy Twin Pack - 10 oz

J-B-Weld-8281-Professional-Reinforced

J-B WELD 8281 PROFESSIONAL SIZE STEEL REINFORCED EPOXY TWIN PACK - 10 OZ Spotlight
Brand :    j-b weld
Size :    10 oz, 2 Pack
Weight :    0.80 pounds
Model :    8281
Quantity :    1
Order click here :    normally ships in 24 hours
Automotive Parts And Accessories :    Best Auto Accessory (j-b weld) reviews for J-B Weld 8281 Professional Size Steel Reinforced Epoxy Twin Pack - 10 oz available as-of ( Oct 2019 )
Stays pliable for 30 minutes after mixing, sets in 4-6 hours and cures fully in 15-24 hoursFor strong permanent repairs on automotive, plumbing, marine, crafts and other projectsStrong and nontoxic after it has set and temperature resistant up to 550FCan be formed, drilled, ground, tapped, machined, filled, sanded and paintedTensile strength: 3960 PSI

Milton S-153 1/4" NPT Lever Style Blow Gun

Rubber Tip Straight Blow Guns Are Perfect To Use Where Leak-proof Connection Is Required When Blowing Out Fluid Lines. A Must Where Metal Tip Could Mar Delicate Finish In Molds Or Painted Surfaces. Also Offers A Tight Fit.

Milton S-153 1/4" NPT Lever Style Blow Gun

Milton-S-153-Lever-Style-Blow

MILTON S-153 1/4" NPT LEVER STYLE BLOW GUN Spotlight
Brand :    milton industries
Color :    United States
Size :    Single
Weight :    0.32 pounds
Model :    S153
Quantity :    1
Order click here :    normally ships in 1-2 business days
Home Improvement :    Best Tools (milton industries) reviews for Milton S-153 1/4" NPT Lever Style Blow Gun available as-of ( Oct 2019 )
Made in USA11.4 standard cubic feet per minute at 100 pounds per square inchMaximum working pressure of 150 pounds per square inch1/4" national pipe thread air inlet

J-B Weld 50101 MinuteWeld Instant-Setting Epoxy Syringe - Dries Clear - 25ml

J-b Weld Minuteweld Syringeminuteweld Is A Special Formulated High-strength Two-part Instant Setting Epoxy. Minuteweld Will Set Under Most Temperature Conditions In One Minute. Minuteweld Is Designed To Adhere To Multiple Surfaces And Can Be Used On Ceramic Tile Glass Stone Most Plastics Wood And Metal. Use On:automotiveceramiccloth/carpetepoxy And Adhesivesfiberglassplastic/composite/pvcand Moreinstructions1. Prepare: Clean Surface Area Of Dirt Grease Oil Paint Or Loose Debris. For Best Results Use A Detergent Or Degreaser To First Clean The Surface Then Roughen Surface With File Or Coarse Sandpaper To Provide The Best Repair. 2. Mix: After Removing The Replaceable Cap Press Down On Plunger And Squeeze Equal Amounts Onto A Disposable Surface And Mix Thoroughly. 3. Apply: Apply With Appropriate Tool In An Even Coat Weld Bead Or Extruded Shape As Needed. 4. Dry: Sets In 1 Minute. Cures In 1 Hour. If Temperature Is Below 40 Degrees Fahrenheit Then Set Time Is Longer. J-b Weld Is Proudly Made In The Usa

J-B Weld 50101 MinuteWeld Instant-Setting Epoxy Syringe - Dries Clear - 25ml

J-B-Weld-50101-MinuteWeld-Instant-Setting

J-B WELD 50101 MINUTEWELD INSTANT-SETTING EPOXY SYRINGE - DRIES CLEAR - 25ML Pros
Brand :    j-b weld
Size :    25 Milliliter
Weight :    0.30 pounds
Model :    50101
Quantity :    1
Order click here :    normally ships in 24 hours
Automotive Parts And Accessories :    Best Auto Accessory (j-b weld) reviews for J-B Weld 50101 MinuteWeld Instant-Setting Epoxy Syringe - Dries Clear - 25ml available as-of ( Oct 2019 )
Clear, instant setting two-part epoxy sets in 1 minute and cures in 1 hourNo mess, no waste cap screws on one way to eliminate accidental mixing and ensure it won't dry outTensile strength of 2850 PSI for a strong, permanent bondGreat for tile, most plastics, ceramic, glass and moreJ-B Weld is proudly made in the USA

J-B Weld 8267-S SteelStik Steel Reinforced Epoxy Putty Stick - 2 oz

J-b Weld Steelstik Epoxy Putty Sticksteelstik Is A Hand-mixable Steel-reinforced Non-rusting Epoxy Putty That Quickly Repairs Or Rebuilds Anything Made Of Metal. After Mixing It Forms An Industrial-strength Polymer Compound That Can Be Molded Into Shapes Or Used To Build Up Patch And Repair Steel Components. Steelstik Sets In 3-5 Minutes And After 60 Minutes Can Be Drilled Tapped Machined Ground Filed And Painted. Steelstik Cures To A Dark Grey Color Is Rated At A Tensile Strength Of 900 Psi And Will Withstand Temperatures Up To 300 Degrees F. Use On:automotivebrickceramicconcretemetalunder Water/wetand Moreinstructions1. Cut:remove Required Amount Of Putty. 2. Mix: Thoroughly Knead Putty With Fingers To A Uniform Color. 3. Apply: Press Putty Firmly To The Surface To Be Repaired. J-b Weld Is Proudly Made In The Usa

J-B Weld 8267-S SteelStik Steel Reinforced Epoxy Putty Stick - 2 oz

J-B-Weld-8267-S-SteelStik-Reinforced

J-B WELD 8267-S STEELSTIK STEEL REINFORCED EPOXY PUTTY STICK - 2 OZ Reviews
Brand :    j-b weld
Color :    Dark Gray
Size :    1-Pack
Weight :    0.11 pounds
Model :    8267-S
Quantity :    1
Order click here :    normally ships in 24 hours
Automotive Parts And Accessories :    Best Auto Accessory (Automotive Parts And Accessories) reviews for J-B Weld 8267-S SteelStik Steel Reinforced Epoxy Putty Stick - 2 oz available as-of ( Oct 2019 )
Easy and simple use kitThe product is steelstik epoxy stickCan be drilled, filed, tapped, machined and paintedSteel reinforced epoxy putty repairs anything made of metalWill cure on wet and dry surfaces, even completely submerged in gasoline or waterThe product is manufactured in United states

3M 32035 Imperial Wetordry 9" x 11" P800 Grit Sheet

3m Imperial Wetordry Is Designed To Sand Clear Coat Areas To Prepare For The Application Of Color Or Clear Coats. Provides A Uniform Fast Cutting Long Lasting Abrasive Save Time While Providing A Consistent Finish.

3M 32035 Imperial Wetordry 9" x 11" P800 Grit Sheet

3M-32035-Imperial-Wetordry-Sheet

3M 32035 IMPERIAL WETORDRY 9" X 11" P800 GRIT SHEET Features
Brand :    3m
Size :    1
Weight :    3.32 pounds
Model :    32035
Quantity :    5
Order click here :    normally ships in 24 hours
Automotive Parts And Accessories :    Best Auto Accessory (3m) reviews for 3M 32035 Imperial Wetordry 9" x 11" P800 Grit Sheet available as-of ( Oct 2019 )
For use with a 3M Sanding Block to produce a uniform finish3M ImperialTM Wetordry sheets are used in wet and dry sanding applications such as scuffing paint, fine featheredging of auto body primer and paint or the final sanding step before priming auto body panels.3M Wetordry Papers provide excellent flexibility for finishing and polishing plastics, metal and coatings.Using the product wet limits dust in the airThe 800 grit sandpaper is the most flexible backing with more consistant scratch pattern make this 3M's best wet sanding product1000 grit Wetordry for sanding primer and scuffing the blend area prior to painting

J-B Weld 8276 KwikWeld Quick Setting Steel Reinforced Epoxy - 2 oz, Pack of 2

J-b Kwikweld Is A Fast Setting Version Of The Original J-b Weld Two-part Epoxy Cold Weld System That Provides Strong Lasting Repairs To Metal And Multiple Other Surface Types. After Mixing It Forms A Permanent Bond And Can Be Shaped Tapped Filed Sanded And Drilled After Curing. J-b Kwikweld Has A 1:1 Mixing Ratio Sets In 6 Minutes And Is Fully Cured In 4-6 Hours. J-b Kwikweld Cures To A Dark Grey Color Is Rated At A Tensile Strength Of 2424 Psi And Will Withstand Temperatures Up To 300f.

J-B Weld 8276 KwikWeld Quick Setting Steel Reinforced Epoxy - 2 oz, Pack of 2

J-B-Weld-8276-KwikWeld-Reinforced

Review from R. Smith, Georgia Easy To Use Good Strong Adhesive Accidently Sawed Part Way Through My Aluminum Miter Guide This Filled And Strengthen To A Like New Condition Saving Me Hundreds Of Dollars. Thank You.

J-b Weld 8276 Kwikweld Quick Setting Steel Reinforced Epoxy - 2 Oz, Pack Of 2 (J B Weld) Review

Review from I. Rebecca, Worcestershire 
Gotta Love Jb Weld - Really Works Really Strong. Highly Recommended For Many Years - Still The Best If Used Properly.
J-B-WELD-8276-KWIKWELD-QUICK-SETTING-STEEL-REINFORCED-EPOXY---2-OZ,-PACK-OF-2-(J-B-WELD)
Image of J-b-weld-8276-kwikweld-quick-setting-steel-reinforced-epoxy---2-oz,-pack-of-2-(j-b-weld)"When They Say 5 Minute Set Time They Mean It. Mix Only What You Need For The Current Joint And Work Quickly."

Excellent Epoxy Set Time Is Quick Don't Mix More Then A Teaspoon Or Two At A Time. Stays Glossy And Sticky For Only Two Or Three Minutes Apply To Surfaces To Be Bonded And Clamp Before It Loses The Glossy Appearance For Best Bond.

Z. Rose, Sandwell

J-B WELD 8276 KWIKWELD QUICK SETTING STEEL REINFORCED EPOXY - 2 OZ, PACK OF 2 Benefits
Brand :    j-b weld
Size :    2 oz (2-Pack)
Model :    8276
Quantity :    2
Order click here :    normally ships in 24 hours
Automotive Parts And Accessories :    Best Auto Accessory (j-b weld) reviews for J-B Weld 8276 KwikWeld Quick Setting Steel Reinforced Epoxy - 2 oz, Pack of 2 available as-of ( Oct 2019 )
Once cured it forms a permanent bond and can be shaped, tapped, filed, sanded and drilledSets in 6 minutes and cures dark grey in 4-6 hoursWill withstand temperatures of up to 300 degrees FahrenheitFast setting version of The Original J-B Weld two-part epoxy cold weld systemRated at a tensile strength of 2424 PSI

Lisle 34550 Handy Packer Bearing Packer

Lisle Handy Packer Works On Bearings Up To 3. 5" O. D. The Grease Stays In The Tool Cavity Not On Your Hands. To Pack A Bearing Place The Bearing On The Piston Press Down On The Cap Until The Old Grease Is Forced Out And The New Grease Shows On Top Of The Bearing.

Lisle 34550 Handy Packer Bearing Packer

Lisle-34550-Handy-Packer-Bearing

LISLE 34550 HANDY PACKER BEARING PACKER Advantage
Brand :    lisle
Weight :    0.85 pounds
Model :    34550
Quantity :    1
Order click here :    normally ships in 24 hours
Automotive Parts And Accessories :    Best Auto Accessory (Automotive Parts And Accessories) reviews for Lisle 34550 Handy Packer Bearing Packer available as-of ( Oct 2019 )
Works on bearings up to 3.5" O.D.Flushes out old grease and repacks bearings with less mess
J-b Weld 8265s Original Steel Reinforced Epoxy Twin Pack - 2 Oz (pack Of 2) (J B Weld) Price : 11.92, was : 0 as 2017-01-18
USUKDEFRESITJPCNCAGlobal
United States
Great Britain
German
France
Spain
Italy
Japan
China
Canada
World Wide
J-b Weld 8265s Original Steel Reinforced Epoxy Twin Pack - 2 Oz (pack Of 2) (J B Weld) Reviewed by on jerdus.com

Top j-b weld 8265s original steel reinforced epoxy twin pack - 2 oz (pack of 2) (j b weld) Content

The F.A.Q. for J-b Weld 8265s Original Steel Reinforced Epoxy Twin Pack - 2 Oz (pack Of 2) (J B Weld)

When to use epoxy cement. When you need a strong rigid workable (e. G. Sandable and/or paintable surface) adhesive, particularly for use on metal or hard plastic, epoxy is usually the best choice. Most epoxies dry with little running or shrinkage, and so are good for filling gaps. The major drawback to epoxies is that they consist of two parts (resin and hardener) which must be mixed in small batches, and then applied with your own applicator (e. G. , a toothpick or popsicle stick). Some are packaged in a dual-syringe-but that is not an adequate solution, because the components must still be manually mixed in order harden to maximum strength. . When to use jb-weld. Jb-weld is a very strong epoxy cement. Jb-weld is the cement/glue of choice when joining metal parts or filling holes in metals. Otherwise, ordinary epoxy cement or other types of cements/glues are usually better choices. Some other reviewers have complained that the descriptive name "weld" is inappropriate-to some extent that's true. Jb weld can do some jobs welding can't. Conversely some simple welding jobs like joining two thin metal rods at right angles are difficult with jb weld. . How to use jb-weld. General principles: although jb weld makes an excellent filler-and can even be used to cast small parts, it is not remotely as strong as real metal used this way. Whenever possible, use jb weld as an adhesive-a very thin layer of jb weld holding two pieces of metal together. Always reinforce with metal pieces when possible. For example, rather than building up a massive flange with jb weld, you might be able to use scrap peice of metal to form most of the flange, held in place with jb weld. The greater the relative surface area of contact, the strong the bond will be. . Surface preparation: as with any adhesive, the surface must be clean and rough. Clean with a solvent (according to another reviewer, acetone is the best solvent for this purpose, but rubbing alcohol will work), roughen the surface, then clean with the solvent again. Use a clean cloth for each application of solvent. I generally use a small grinding wheel in a dremel tool to roughen the surfaces. You can also scratch the surface with a knife, or use coarse sandpaper, or both depending on the material. . The solvent cleaning is for removing the last traces of oil from clean surfaces. If the parts are oily, even multiple cleanings with solvent may not be enough-you may redeposit oil from your cleaning cloth or as the solvent evaporates on the surface. So, if you can detect any oil on any portion of the part, or if you have any doubt, clean it with a degreaser first. If you do not have a commercial degreaser handy, a paste of laundry detergent and a stiff brush may do the trick. Only when you are certain that there are no traces of oil is it time for the solvent cleaning(s). . Joining broken parts: if you are joining broken parts, with a clean but irregular matching surfaces, limit the roughening to scratching with a wire brush or etching with an acid (but be sure to wash off all traces of the acid). Apply a thin uniform layer of jb weld, lightly clamp together hard enough to squeeze out any excess. Sometimes a thick rubber band is perfect. Often you can arrange pieces so that the weight of the top piece will hold the joint together until the jb weld cures. Sometimes you can place a weight (such as a brick) on top to apply gentle pressure. Do not remove the clamp or pressure until the jb weld has cured completely. After an hour or two, after the glue has set but is still soft, you can cut off any excess with a knife or razor-but if you don't need to cut the excess off, don't. Often you can build-up the surfaces around a break for added strength. Sometimes blue painters tape can be used to help hold pieces together while the glue sets, and/or to make a temporary stand to hold the pieces in the best orientation.  scotchblue painter's tape for multi-surfaces 2090-. 75a, 3/4 inches by 60 yards, 1 roll. . Joining dissimilar parts: minimize any gaps if possible, e. G. , by sanding if possible so that the contact as perfect as possible. If you will be filling substantial gaps, sometimes it is helpful to cover openings with blue painters tape to prevent the jb weld from flowing away and leaving gaps. . Joining long thin parts (rods or sheets): try to overlap if possible, or reinforce them with a similar overlapping peice of metal glued in place with jb weld. To join a 1/8" steel rod, to another 1/8" steel rod, forming a "t" (a common and easy welding job, almost impossible with just jb-weld), cut two 1"-long "l's" from a heavy-paper clip, (or make l's from similar wire), and embed those with jb-weld on opposite sides of the joint. You can further strenthen the joint by wrapping fine steel wire around the rods holding the "l"s in place-before covering it all with jb-weld. Be sure to thoroughly clean the rods and wires first (see below). For small parts, or when wire wouldn't work well, unwaxed dental floss is remarkably strong, and can do an excellent job of reinforcing joints (when embeded in jb weld). Ideally, apply the jb weld, then wind the floss tightly into the soft jb weld. . Filling holes: don't forget to prepare the surfaces as described above-even if you can only roughen the surfaces with an ice pick or awl. Jb weld shrinks very little as it cures so fill the hole completely. If it is possible to sand the surface when the jb weld has hardened, then overfill the hole slightly. Since jb weld flows a little until it sets, the surface should be horizontal. If not horizontal, you can apply the jb weld and then cover the hole with blue painters tape until the jb weld sets. Depending on the job, it is often a better strategy to fill the gap as much as possible with a piece (or pieces) of metal embedded in jb weld that a single mass of pure jb weld. . Reinforcing a leaking pipe: work jb weld into a piece of fiberglass cloth or with a spatula, apply, and then add more jb weld to any thin spots and to feather out the edges. You may have to apply several layers of the jb weld-saturated fiberglass cloth. Sometimes wire cloth (window screening) can be used. . Holes in car body panels etc: if you can cover at least one side of the hole with a piece of sheet metal (held in place by jb weld) that is a good strategy-the combination of pop-rivets and jb weld often works especially well, even if you ultimately sand the heads of the pop rivets away.  tekton 6555 rivet gun with 40-pc. Rivets. . Mixing: follow the instructions. A paper plate can be a good mixing surface; popsicle sticks are the best mixing tools. Beware that you must use the same amount of resin and hardener, and they must be very thoroughly mixed. Mix until you are certain that it is completely and thoroughly mixed, and then continue mixing for twice that time. Seriously! . . Curing: follow the instructions, but wait longer than recommended: the longer you wait the stronger the bond. A a day or two at 70 or 80 degrees is a reasonable minimum. Note that epoxies do not "dry"-there are no solvents to evaporate, instead a chemical reaction hardens the cement (a plastic resin). Chemical reactions are proportional to temperature (the rule of thumb is that for each 10 degrees, the reaction speed doubles). Using the rule of thumb, if it takes 1 day to cure at 80 degrees, then it takes 16 days to cure at 40 degrees, and that's only to minimally cured. Okay, i know that waiting this long is not practical in many circumstances-you can probably get away with curing for 4 hours at 90 degrees (but don't go much higher than 90 degrees), and "take it easy" for a couple of days. . When to use other epoxies. For materials other than metal, particularly for rigid plastics, other epoxies are usually better than jb weld. Some epoxies are clear, or white, or specialized for particular purposes. For example clearbond h-3s clear strong epoxy adhesive syringe - . 85oz. . When to use quick-epoxies. Ordinary (slow) epoxies (whether jb weld or other epoxies) dry harder than quick epoxies and are generally the best choice. Maximum strength is the whole point of epoxies-if you don't need maximum strength-you probably do not need epoxy. Use quick epoxies when 1) the hardening speed is essential, 2) when the item cannot be supported in the required orientation while the epoxy sets (at least several hours), or 3) when you have to absolutely minimize flowage. Super-glue is often a good alternative in such situations. . When to use other cements or glues. While epoxies are ideal for a few specific uses (primarily when you need a rigid cement for metal or rigid plastic)-there are many situations when other types of glue are better choices. Epoxies are generally not recommended for flexible surfaces, such as leather, wood, or flexible plastic, and generally do not adhere well to glass, etc. While epoxies may work with porous surfaces (paper, wood, ceramics, etc. ), other adhesives are usually better. . White glue: for most light-duty indoor household applications which do not have to be waterproof, ordinary household white glue is safe, cleanup is very easy, and in most cases repairs are redo-able if you make a mistake. White glue shrinks a great deal as it dries, and so is not good for filling holes or large gaps. For example: elmer's all multipurpose white glue, 7 5/8 oz. (e379). . Glue stick: think of glue sticks as thick white household glue in stick form. Glue sticks are great with paper, but have few other applications. Avery glue stic, 0. 26 oz, pack of 6, (98095). . Wood glue: carpenters's wood glue is essentially water-proof (when dry) white household glue. It penetrates and strengthens the wood better than any other type of glue. It is safe, and cleanup is easy. If the joint breaks again (because the wood is weak), it can be re-glued. For example: elmer's e701 carpenter's wood glue 8-ounce. . Goop: goop will bond virtually any material, including leather, plastics, glass, and metal. The bond is clear, very strong, waterproof, and hard but flexible. Since goop is clear, if a little extra oozes out, it is barely noticeable. I've used goop to repair ceramic plant pots, water hoses, and shoes; to seal holes in air-mattresses, to close small holes in window screens, as plumbers paste in assembling plumbing parts, to i also use it to seal rust spots on my dishwasher rack-the goop it also makes a "cushioned" surface that will prevent scratches to dishes. Goop is particular good for repairing damaged electrical cords.  amazing goop all-purpose household goop, 3. 7-ounce tube 130012. . Silicon glue: silicon glue is best for glass, and when you want a truly flexible connection (for example, to absorb vibrations). It is a good alternative for goop for general household use on glass, plastic, and metal when you do not need the maximum possible strength. It is safer than goop, and cleanup is easier. Like goop, silicon glue takes days to reach reasonable strength, weeks to reach maximum strength. For example: ge silicone ii household glue, 2. 8 oz. . Fabric glue: beacon fabri-tac permanent adhesive, 4-ounce works amazingly well on fabrics, saturating the surfaces enough to provide a very strong bond, but without soaking through. Depending on the application, fabric glue can be better than sewing. It remains very flexible, e. G. , it would probably be great on leather or heavy vinyl (e. G. , women's handbags, shoes, luggage, etc. ). . Super-glue (krazy glue): super-glue is very strong, rigid, and fast. In many ways it is similar to 2-minute epoxy-except that no mixing is required. Although very hard, super-glue is brittle, and so, is not recommended for flexible objects. Super-glue is hazardous in that it can easily glue fingers (etc. ) together. Previously, i used super-glue frequently on objects (e. G. , jewelry) when a clear bond was required-however, goop is better for such applications, safer, and more conveneient. Opened super-glue keeps poorly, even in tighly sealed glass containers-so i recommended packages of multiple very small tubes.  bazic super glue, 3 grams 0. 10 ounces, 6 per pack. . Liquid nails/construction adhesive: when you need to permanently join a large amount of surface, of almost any kind, construction adhesive is usually ideal. If you need to join 2 2x4s to make a 4x4 construction adhesive is better than nails. Most construction adhesives are slightly flexible, and so can even be used on leather (i. E. , to repair a loose shoe sole), etc. Construction adhesive may leave a stain on porous surfaces, and may stain-through thin surfaces. For small projects, goop is usually a better choice. . Caulking compound: you can think of caulking compound as white household glue with alot of inert filler-to use when you need to fill holes. As an adhesive, it is the weakest on this list, but is strong enough for many purposes when spread over a large surface, such as the back of a ceramic tile. A few years ago, i made a brick column to support a mailbox. Traditionally, i should have used mortar-which would have been very time consuming. I could have used construction adhesive (albeit any excess that squeezed out would have been ugly)-but caulking compound was quick, cheap, looks good, and was more than adequate for the job. . Hot glues: in short, if you really need the glue to set quickly, particularly if you've got alot of gluing to do - consider hot glues. As several commenters have pointed out, there is a whole world of hot glues (which come in the form of glue sticks which are used in glue guns), many of which work better, or are more convenient, than comparable cold glues. In general, the most important attribute of hot glues is that the glue sets very quickly - in some cases - within seconds. Since most hot glues set quickly, it is tempting to apply them too thickly. Even with hot glue, for maximum strength, you should use the smallest amount that does the job, and apply moderate pressure until the glue sets. Unfortunately, i have only limited experience with hot glues, and cannot supply specific suggestions for specific purposes.

A number of questions have been asked here.

Q&A

(0) Question: Block crack between cyls 5 & 7 against the head, at the narrowest point between cyls. both cyls are sleeved. will jb hold the temp without breaking do


(1) Question: I have a number of small leaks in an older aluminum boat- would jb work for a repair on this as a weld/filler for small punctures? thanks


(2) Question: Will this stop an exhaust leak right where a donut goes flanges off of the manifold? or which jb weld would work


(3) Question: Can i use this item with car a/c condensator between alluminium and bronze


(4) Question: Is there any way of removing hardened jb weld of soften it once it's hardened?


(5) Question: My motorcycle's clutch handle broke in half in a fall, would this be able to reunite the two pieces?


(6) Question: Can this seal a air compresser tank at 125psi. has a small hole?


(7) Question: Can this be used to seal leaking auto battery top- sulfuric acid resistant? i read about a masterbond epoxy for such, but $. thanks


(8) Question: Can this seal a cracked oil pan



(note) Question: where/how to get J B Weld (manufacturer's brand) accessories & similiar J B Weld's products

Answer:

Click the marked text to copy link to Clipboard

And this is great stuff. Some pointers. Epoxy glues have a limited shelf life. Buy yours at a small store where the merchandise doesn't move quickly, or keep it 5 years on the shelf and it won't work as well. Don't apply it at temperatures below 60 degrees. Spend at least 2 or 3 minutes mixing it. I use a timer to be sure. Surface preparation is the key. It must be completely grease free. I use naptha (lighter fluid) if the part is very greasy, then alcohol, and acetone in that order. Or better yet, brake cleaner or gun scrubber, neither of which appear to leave any trace. Whatever, clean surfaces as much as you think , then some more. . The surface must be rough. I use a file, very rough ( 40 or 60) sandpaper or a sharp exacto blade to make multiple cross hatch cuts- this will even work on most steels . Roughness and cuts increase the surface area, if the cuts are done right at an angle , undercut, they can also make the glue hold better. Don't touch the cleaned area after cleaning with bare fingers mix a bit more than you need , larger quantities are easier to mix 50-50. Apply the mix carefully, put the pieces together so they don't move for at least 8 hours. You can speed up setting by placing the part in the sun on a warm day. I use an oven set at 100 degrees f for small parts. It is best to wait for initial l tackiness before doing this. J b weld is very slow drying. Do all that and the bond is very strong. . . Re shelf - the makers of epoxy say it has a long (years) shelf life, but only if unopened. I prefer fresh stuff , why take chances on critical jobs . If it's nor important feel free to try/


Adhesives 12981751, Automotive 18148651, Body Repair & Restoration Chemicals 11981751, Oils & Fluids 19781751Top J-b Weld 8265s Original Steel Reinforced Epoxy Twin Pack - 2 Oz (pack Of 2) (J B Weld) FAQ Content

Best j-b weld 8265s original steel reinforced epoxy twin pack - 2 oz (pack of 2) (j b weld) in review

Great product

V. Anonymous, Newfoundland and Labrador

You might like to see Keeper (04226) 24" X 2" Premium Axle Strap D-ring Auto Accessory 04226
  • Advantages: Stamped steel Delta rings
  • Advantages: 2" x 24"; 3,333 pounds working load limit premium axle strap
  • Advantages: Hi-test 10,000 pounds webbing with protective sleeve
keeper (04226) 24" x 2" premium axle strap d-ring: keeper auto accessory keeper's 24" x 2" premium axle strap d-ring features 3 333 pounds working load Keeper (04226) 24" X 2" Premium Axle Strap D-ring (Auto
Or you might like to consider J-b Weld 8267-s Steelstik Steel Reinforced Epoxy Putty Stick - 2 Oz Auto Accessory 8267 S
  • Components: The product is steelstik epoxy stick
  • Components: Easy and simple use kit
  • Components: The product is manufactured in United states
j-b weld 8267-s steelstik steel reinforced epoxy putty stick - 2 oz: j b weld auto accessory j-b weld steelstik epoxy putty stick. . steelstik is a hand-mixable J-b Weld 8267-s Steelstik Steel Reinforced Epoxy Putty Stick - 2 Oz (J B

O. Franklin, Bexley says

I bought a new black granite sink. I put it in, which is a hassle and takes a bit of time. I then noticed that the sink had a very small hole in the back inside which did not go entirely through the sink. It was likely just a bubble in the granite mix that came to the surface and remained unseen until it got to me. The hole was about a quarter of an inch in size. I didn't want to take out the sink and replace it for two reasons: one it is a lot of work and two it seems like such a waste of materials in the environmental sense. I called the company and they would replace the sink free of charge (not install). I asked them if i fixed the hole in some way if it would void the lifetime warranty. They said "try it" if it doesn't work we will still cover it. That is where the j-b weld comes in. The black color of the epoxy is almost a perfect match for the black sink. Since i've used the j-b before i know it is strong. I carefully filled the hole. Later i asked my wife if she could find the repair and it took her some time to find it. It has been about a year since the repair and it is still perfect. Unless you knew the repair was there you would not find it.

C. Jacqueline, Niedersachsen

Use it wisely! so i have a 2001 honda prelude, living in rural areas and my car being so dammmn low you could suspect i "bottom out" a lot. With that said i recently found a crack/hole in the bottom of my engine. Due to a rock or something i don't know. Anyway. Jb weld helped me patch up that small opening in the engine. How long will it last? who knows. I did it about a 2 weeks ago and it seems to stop the oil leak/ oil burning smell (due to the oil leak). What i don't recommend is just slapping it on there. Prep is everything! spray it with brake cleaner, sand that sucker down, make it smooth, use a spatula, let it cure, sand it again , and do another layer for good measures. . All in all j-b weld seems to work. Give it a try if you don't want to put 2grand/3grand on a new engine (let alone start eating something less than ramen for a year(s) (college life is crazy)).

L. Hakala, Haute-Normandie says

J-b weld is just stronger than other epoxies i've tried, and resists heat better, too. Machines well when cured. My best experience with it was using it with some fiberglass cloth to repair a crack in the plastic top of an otherwise fine radiator, which broke when stress was applied to a mounting bracket. The repair lasted maybe five years, and i sold the car with the repair. Too bad the person we sold the car to got drunk and totaled it within a month, or maybe this testimony would be even better. Recently used it to build up the door hinge in our shower door, which had worn down over the years to the point where you could barely close it. So now the weight of the door is basically riding on this stuff, and works like new. Shelf life of this stuff is many years, in my experience. I'm assuming here they haven't changed the formulation, because i haven't even cracked the new package yet. I'm still using up the last of my old one.

U. Irene, Utah

Perfect for bonding aluminium.

G. Monique, North Tyneside says

A handy tool

O. Kelly, Sutton

What can you say but this stuff if fantastic! been using jb weld for 30 years or so and its never let me down. Latest use is as a foundation for bondo when filling small body holes.

U. Brenda, Hampshire says

I hate the choices at the big box stores and have had poor results from several name brands. I needed to 'weld' some dissimilar metals so i bought this larger size jb weld. First, this is not the tiny 1 oz tubes that don't have enough material to glue anything other than costume jewelry. Of course, 10 ozs is more expensive, but it also has a long shelf life so if you are any kind of handyperson, you will likely use it before it expires. (also, it is not in those silly, useless "injector" tubes that look like syringes. I've tried the injector style tubes and they are a total waste of money imo. If there is a secret to getting the two parts to come out of the injestor tubes, i haven't mastered it yet or at my age, maybe i just lack the hand strength to compress the injectors. Trying to squeeze a very viscous glue through two tiny openings, is near impossible and i ended up throwing the tubes away. ) these two parts come in toothpaste liike tubes and are easy to use, squeeze and estimate equal amounts. Both components are very thick. For best results, mix well, and then keep mixing for at least three minutes! this is not fast drying, so you have several hours of workability, but within 24 hours at room temperature, it feels as hard as metal. Even though the mixed epoxy is pretty thick, it will "run" for several hours so plan accordingly. . Update: 1/16/17 two years later, my original box and tubes are still going strong, and i haven't had to buy more yet. Very happy with product . Every use i have come up with, it seems to work well. I actually used it to "weld" a metal gate post to a mounting base bracket and two years later, it hasn't failed. One comment: i recently used it to attach a small exterior item in 60 degree weather, and it took over 24 hours to set up. Although i expected slower cure times for cold weather uses, this was a little longer than i anticipated. Moral: be prepared for very slow cure times for cold temp use.

W. Gloria, Poitou-Charentes

This is the cheapest way to get j-b weld for sure. Just be carful that you mix the two together very well, don't be lazy and just squirt the two on top of each other and then clamp (like i did) my only complaint with this is that it can be tough to squeeze the tubes enough to get it out when the tube is half full or less (especially if its cold). If you've got herk hands or keep this in a warm place that should not be a problem. Be carful to lot let any of the mixed compound get on the tip of the tube unless you want to cut the lid off. I have used this on busted transmission fluid lines and numerous other things, it works.

W. Anonymous, Bradford says

A workbench staple.

N. Rhonda, Cheshire

This is my favorite epoxy. I've fixed many things with this epoxy over the years all around my house, yard, and workshop. It has never failed to perform wonderfully! the latest thing was a tiki lamp that had a metal support rod come loose at the weld on the main pole. I sanded the end of the support rod and sanded the broken weld spot on the main pole, then applied the j-b weld. The next day, it was ready for use and seems stronger than the original weld. Then there was the lamp base, and the 10x10 canopy support, and the pool's net skimmer, and the windmill, and many more items. All fixed with j-b weld!

D. Guest, Haringey says

Used this epoxy to re-fasten knob handles to the door on my woodstove. Was easy to mix, plenty of "open time" to place the components where i needed them before it started to cure (cured to 'stiff' in about an hour or so). Waited 24 hours for the epoxy to fully cure (per the instructions) before cranking up the woodstove again and the knobs are now very secure.

L. Smith, Thueringen

This is my favorite epoxy. very strong



Leave a Reply

You must be logged in to post a comment.


Top j b weld 8265s original reinforced Review Content

Related Products

Product Image Gallery

Top-j-b-weld-8265s-original-reinforced-41741fwgf9l6-Content